Desa LNT-2 8-inch, LNT-3 12-inch, EL-7 14-inch, EL-7 16-inch, LNT-2 10-inch Filling OIL Tank, Edge

Page 7

OWNER’S MANUAL

ASSEMBLY

Continued

Tapping	Front Hand		Cutting
Screw		Towards
	Guard		Edge
		Guide

		Bar Nose

	Cutting
Guide Bar	Edge	Saw
Guide Bar		Chain
Bolts
Mounting	Drive
Stand-Outs	Sprocket

Guide

Bar

Adjusting

Hole

Guide Bar

Nuts

Figure 3 - Assembling Guide Bar, Chain, and Hand Guard

	Adjusting	Adjusting
	Block
		Plate

Adjusting

Screw

Sprocket

Support

Figure 4 - Part Locations For Assembling Guide Bar

FILLING OIL TANK

1.Remove oil cap.

2.Fill oil tank with SAE #30 motor oil. Note: For temperatures below -1°C,

use SAE #10 oil. For temperatures above 24°C, use SAE #40 oil.

3.Replace oil cap at once. Tighten oil cap ﬁrmly for good seal. This will avoid oil seepage from tank.

4.Wipe off excess oil.

Note: It is normal for oil to seep when saw is not in use. Empty oil tank , tighten oil cap, and store upside down after each use to prevent seepage.

105020	7	For more information, visit www.desatech.com

Image 7

Contents Electric Chain SAW Auto Information Symbols Information SymbolsKickback SafetyKickback Safety Devices On This Saw Before Operating Chain SAWChain SAW Operation Saw Maintenance and Kickback SafetySecure wood you are cutting by using clamps or chocks Pushback and PULL-INChain SAW Names Terms Maintenance and Storage of Chain SAWRear Handle Handle located at rear of saw body Product Identification AssemblyUnpacking Edge Filling OIL TankOperating Chain SAW SAW Chain Tension AdjustmentExtension Cords Cutting with the Chain SAW Oiling ChainTrimming a Tree Pruning Felling Cut Felling Procedure Felling NotchFelling a Tree Cutting Down a Tree Before Felling a TreeCut log from top see Figure Bucking a LOGLimbing a Tree Entire Length Of Log On GroundLog Supported On One End Cleaning and MaintenanceCleaning SAW Body Care of Guide BARSharpening Cutters Normal Guide Bar MaintenanceSharpening Your SAW Chain Items Needed to Sharpen ChainReplacing Saw Chain Replacement PartsStorage Filing Cutter Depth GaugesObserved Fault Possible Cause Remedy TroubleshootingLNT-2 and LNT-3 Illustrated Parts BreakdownDescription Parts ListEL-7 QTY Industries of Canada, Inc Keep this WarrantyCopy Tronçonneuse Électrique Prime Description Symboles Description SymbolesCause du recul Avertissements Pour LA SécuritéAvant Dõutiliser LA TRON‚ONNEUSE ReculUtilisation DE LA TRON‚ONNEUSE POUSSƒE ET TractionEntretien de la trononneuse et protection contre le recul Causes de la poussŽe et de la tractionEntretien ET Remisage DE LA TRON‚ONNEUSE Vocabulaire DE LA TronçonneuseDans un endroit sec Taille Žlagage Coupe des branches d’un arbre sur pied DéballageMontage Nomenclature DES PiècesRemplissage DU Réservoir D’HUILE Utilisation DE LA Tronçonneuse Réglage DE LA Tension DE LA ChaîneProlongateurs DE Cordon Sciage Avec LA TRON‚ONNEUSE Lubrification DE LA CHAëNETaille Dõun Arbre ƒlagage Trait dÕabattage Abattage Dõun ArbreAvant dÕabattre un arbre ProcŽdure dÕabattage Sifflet dÕabattageTronçonner la bille à partir du dessus. Voir la figure ƑBRANCHAGETRON‚ONNAGE Dõune Bille Toute la bille repose au solLa bille est soutenue ˆ une extrŽmitŽ Nettoyage ET EntretienEntretien DE LA LAME- Guide Nettoyage DU Carter DE TRON‚ONNEUSEAffžtage des taillants AFFóTAGE DE LA CHAëNEEntretien normal de la lame- guide Outils nŽcessaires pour affžter la chaneLimage des limiteurs de profondeur des taillants Remplacement de la chaneRemisage Pièces DE RechangeREMéDE DépannageDƒFAILLANCE OBSERVƒE Cause PossibleLNT-2 ET LNT-3 Détail DES Pièces IllustréesQuantitŽ 20,3 cm EL-7 QuantitŽ Conserver Cette Garantie Information SUR LA Garantie