Casablanca Fan Company C31UxxZ Prepare for W-84 Wall Control installation - Continued, Figure #4

Page 25

®3

Prepare for W-84 Wall Control installation - Continued

Step 1d. Before attaching the bezel back on to the front of the switch, make sure that the rubber key pad is attached to the locating pins on the bezel as shown in Figure #4.

Step 1e. To attach the bezel back onto the front of the switch you will need to align the four (4) tabs on the bezel with the front of the wall control.Gently press on both top and button of the bezel at the same time, snap the bezel back on to the front of the switch as shown in both figures #5 and #6.

Step 1f. Check your work by pressing on the light, fan, reverse and power buttons, making sure that the buttons do not stick and that each switch functions properly.

RUBBER KEY

PAD

ALMOND	LOCATING
BEZEL	PINS
	(4)

Figure #4

ALMOND

BEZEL

TABS

BEZEL

ALIGNMENT

PIN AND HOLE

Figure #5

ALMOND

BEZEL

TABS

Figure #6

Image 25

Contents Holliston PN C3143001-AT0209C31UxxZ O W N E R ’ S M A N U A LLIMITED WARRANTY Proof of PurchaseTHIS WARRANTY SUPERSEDES ALL HollistonPREVIOUS WARRANTIES Holliston CONTENTSRead and Save These Instructions PN C3143001 AT0608MODEL # C31UxxZ SERIAL No. DJ06Holliston TYPE7-Watt Incandescent Parts GuideUplight Bulbs Adaptor Assembly Blade Iron Screws pre-installed, see pg 13, step 9aSwitch Housing Cap Switch Housing Cap Screws 8-32 x 3/8use only genuine Casablanca blades, light fixtures, and accessories For best performance and for your warranty to be validIntroduction Before You Start Safe UseWhen to Use Extension Poles sloped ceiling installationsMOUNTING RECOMMENDATIONS General Guidelines Calculation of Ceiling AngleCeiling plate Installation Fan Installation Getting StartedInstalling a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet BoxCanopy Installation Lag Screw InstallationCANOPY LOCK WASHERS CANOPY SCREWS Prepare for fan installation as follows IMPORTANT SAFETY INFORMATIONFan Preparation Figure #1 Figure #2Figure #4 Fan Preparation - continuedFigure #5 Install Lightbulbs LIGHTBULB INSTALLATION uplightHanging the Fan Figure #6Canopy Electrical Connections Canopy Hatch and cover ring InstallationFigure #2 Blade Installation Blade InstallationAttach Blade Irons Blade Installation Continued LIGHT FIXTURE Installation optionalBlade screws must be tightened securely before operating the fanNO LIGHT KIT - Installation switch housing and end cap InstallationLight Kit Adaptor Disassembly Switch Housing and Light Kit Adaptor Installation - NO LIGHT KIT Adaptor Installation - Continued NO LIGHT KIT Switch Housing and Light KitAdaptor Installation NO LIGHT KIT - END SCREW Figure #6LIGHT KIT - Installation Adaptor Installation - Continued LIGHT KIT Switch Housing and Light KitFigure #9 Figure #11 Figure #10Figure #12 Figure #14Figure #16 Figure #15Figure #17 Prepare for W-84 Wall Control Bezel replacement as follows W-84 WALL CONTROL INSTALLATIONW-84 Wall control Preparation For use on product with BOTH UP and DOWN LIGHTS ONLYPINS Prepare for W-84 Wall Control installation - ContinuedRUBBER KEY PAD ALMONDsingle W-84 Installation w-84 Control INSTALLATION Installing the W-84 Wall ControlW-84 Wall Control DIP SWITCHES dual W-84 InstallationNEUTRAL Make sure where you are in the sequence to the right Operation PowerOperation Speed Control Operation Reversing AirflowTo dim just the up light changing frequency settingTo dim just the down light NOTE All fans leave the factory set to “1111”++++ Automatic Demonstration ProgramOperation Safe-Exit and light-minder Program To enter the demonstration programOperation Fan-Minder Program Operation Home-Safe Program+ + + In the wall bezel replacement W-84 Wall Control Bezel replacement CONTINUED ALMOND COLORED BEZEL BEZEL BEZEL TABS BEZEL ALIGNMENT PIN AND HOLEALMOND WALL PLATE SCREWS ALMOND COLORED WALL PLATE Troubleshooting tips Dimensions Product SpecificationsWeight Care RecommendationsHolliston