Casablanca Fan Company C31UxxZ switch housing and end cap Installation, Holliston, Figure #1

Page 17
switch housing and end cap Installation

HollistonNO LIGHT KIT - Installation:

switch housing and end cap Installation

NO LIGHT KIT - Installation:

NOTE: If you are installing your fan without a light kit attached as shown in Figure #1, continue with these installation instruction

Figure #1

Switch Housing Hardware (not to scale)

Screw Plug

Light Kit Adaptor Assembly

Step 11a. Locate the light kit adaptor assembly and screw plug as shown in the switch housing hardware section above. You will need to install the complete assembly for no light kit installation.

NOTE: Do not discard screws during disassembly, all screws will be needed for other installation steps within this document.

Light Kit Adaptor Disassembly

Step 11b. Locate and remove the one #8-32 screw that is attaching the bottom cap to the light kit adaptor assembly as shown in Figure #2 and remove the bottom cap. Do not discard screws during disassembly.

Step 11c. Locate and remove the four #6-32 screws from the cap and remove the cap. Do not discard the screws during disassembly.

NOTE: Locate the light kit adaptor as shown in Figure #2, this adaptor plate will need to be attached to the fan during fan installation for light kit or no light kit installation.

SCREW PLUG

SCREW

#8-32

BOTTOM CAP

SCREW

 

#6-32

CAP

LIGHT KIT

PLATE

Figure #2

BOTTOM CAP Light Kit Adaptor Disassembly

SCREW , #8-32

BOTTOM CAP

Figure #3

CAP

Cap SCREW,

 

#6-32

Figure #4

 

15

Image 17
Contents Holliston PN C3143001-AT0209C31UxxZ O W N E R ’ S M A N U A LTHIS WARRANTY SUPERSEDES ALL HollistonPREVIOUS WARRANTIES Proof of PurchaseLIMITED WARRANTY Holliston CONTENTSRead and Save These Instructions PN C3143001 AT0608MODEL # C31UxxZ SERIAL No. DJ06Holliston TYPEUplight Bulbs Parts Guide7-Watt Incandescent Adaptor Assembly Blade Iron Screws pre-installed, see pg 13, step 9aSwitch Housing Cap Switch Housing Cap Screws 8-32 x 3/8use only genuine Casablanca blades, light fixtures, and accessories For best performance and for your warranty to be validIntroduction Before You Start Safe UseWhen to Use Extension Poles sloped ceiling installationsMOUNTING RECOMMENDATIONS General Guidelines Calculation of Ceiling AngleCeiling plate Installation Fan Installation Getting StartedInstalling a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet BoxCANOPY LOCK WASHERS CANOPY SCREWS Lag Screw InstallationCanopy Installation Prepare for fan installation as follows IMPORTANT SAFETY INFORMATIONFan Preparation Figure #1 Figure #2Figure #5 Fan Preparation - continuedFigure #4 Install Lightbulbs LIGHTBULB INSTALLATION uplightHanging the Fan Figure #6Figure #2 Canopy Hatch and cover ring InstallationCanopy Electrical Connections Attach Blade Irons Blade InstallationBlade Installation Blade Installation Continued LIGHT FIXTURE Installation optionalBlade screws must be tightened securely before operating the fanLight Kit Adaptor Disassembly switch housing and end cap InstallationNO LIGHT KIT - Installation Switch Housing and Light Kit Adaptor Installation - NO LIGHT KIT Adaptor Installation - Continued NO LIGHT KIT Switch Housing and Light KitAdaptor Installation NO LIGHT KIT - END SCREW Figure #6LIGHT KIT - Installation Figure #9 Switch Housing and Light KitAdaptor Installation - Continued LIGHT KIT Figure #11 Figure #10Figure #12 Figure #14Figure #17 Figure #15Figure #16 Prepare for W-84 Wall Control Bezel replacement as follows W-84 WALL CONTROL INSTALLATIONW-84 Wall control Preparation For use on product with BOTH UP and DOWN LIGHTS ONLYPINS Prepare for W-84 Wall Control installation - ContinuedRUBBER KEY PAD ALMONDW-84 Wall Control w-84 Control INSTALLATION Installing the W-84 Wall Controlsingle W-84 Installation NEUTRAL dual W-84 InstallationDIP SWITCHES Make sure where you are in the sequence to the right Operation PowerOperation Speed Control Operation Reversing AirflowTo dim just the up light changing frequency settingTo dim just the down light NOTE All fans leave the factory set to “1111”++++ Automatic Demonstration ProgramOperation Safe-Exit and light-minder Program To enter the demonstration program+ + + Operation Home-Safe ProgramOperation Fan-Minder Program In the wall bezel replacement W-84 Wall Control Bezel replacement CONTINUED ALMOND WALL PLATE SCREWS ALMOND COLORED WALL PLATE BEZEL BEZEL TABS BEZEL ALIGNMENT PIN AND HOLEALMOND COLORED BEZEL Troubleshooting tips Dimensions Product SpecificationsWeight Care RecommendationsHolliston