Casablanca Fan Company C31UxxZ owner manual MOUNTING RECOMMENDATIONS General Guidelines

Page 8
MOUNTING RECOMMENDATIONS

MOUNTING RECOMMENDATIONS

General Guidelines

Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation.

Location

Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan.

• For safety reasons, the fan blades must be a minimum of 7' above the floor.

• Do not locate the fan in a doorway or above a swinging door.

In bedrooms, fans work best when mounted above the foot of the bed.

Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues.

In kitchens, be sure to allow for open cupboard doors to clear the fan blades.

Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and warp the blades.

Fan Size

Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may be needed.

sloped ceiling installations

Suggested Extension Pole Lengths

Ceiling Height

Pole Length

8' 0"

3.5"

8' 6"

3.5"

9' 0"

12"

9' 6"

12"

10' 0"

18"

11' 0"

24"

12' 0"

36"

13' 0"

48"

14' 0"

60"

 

Maximum

Extension

Hang-Tru®

angle 32º

Pole

Blades must be a minimum of 7 feet above the floor

7' minimum

When to Use Extension Poles

For optimum performance and appearance, an extension pole should be used with your Casablanca fan when installing on high (cathedral) ceilings or sloped ceilings. Casablanca offers standard poles in increments of 6" up to 5'. Custom poles are available in lengths up to 9'9". See your Authorized Casablanca Dealer for details.

Note: Fan may wobble or vibrate if pole length is not long enough and inside blade is too close to downslope or side wall. Extending pole length will usually solve the problem.

Calculation of Ceiling Angle

Use the tear-off Ceiling Angle Template card inserted in this manual. It provides you with a simple “go” or “no-go” for installing your fan on a sloped ceiling.

EXAMPLE 1

This slope is less than 32º.

It is OK to install your fan.

 

 

This slope is 32º. This is the maxi-

 

mum slope that will allow the fan to

EXAMPLE 2

hang straight down. It is OK to install

your fan.

 

This slope is more than 32º. Your

 

fan will not hang straight down; an

 

adapter is necessary. Contact your

EXAMPLE 3

local Authorized Casablanca Dealer

 

in regards to purchasing a “Sloped

 

Ceiling Adapter.”

6

Image 8
Contents PN C3143001-AT0209 HollistonC31UxxZ O W N E R ’ S M A N U A LTHIS WARRANTY SUPERSEDES ALL HollistonPREVIOUS WARRANTIES Proof of PurchaseLIMITED WARRANTY CONTENTS HollistonRead and Save These Instructions PN C3143001 AT0608SERIAL No. DJ06 MODEL # C31UxxZHolliston TYPEUplight Bulbs Parts Guide7-Watt Incandescent Blade Iron Screws pre-installed, see pg 13, step 9a Adaptor AssemblySwitch Housing Cap Switch Housing Cap Screws 8-32 x 3/8For best performance and for your warranty to be valid use only genuine Casablanca blades, light fixtures, and accessoriesIntroduction Before You Start Safe Usesloped ceiling installations When to Use Extension PolesMOUNTING RECOMMENDATIONS General Guidelines Calculation of Ceiling AngleFan Installation Getting Started Ceiling plate InstallationInstalling a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet BoxCANOPY LOCK WASHERS CANOPY SCREWS Lag Screw InstallationCanopy Installation IMPORTANT SAFETY INFORMATION Prepare for fan installation as followsFan Preparation Figure #1 Figure #2Figure #5 Fan Preparation - continuedFigure #4 LIGHTBULB INSTALLATION uplight Install LightbulbsHanging the Fan Figure #6Figure #2 Canopy Hatch and cover ring InstallationCanopy Electrical Connections Attach Blade Irons Blade InstallationBlade Installation LIGHT FIXTURE Installation optional Blade Installation ContinuedBlade screws must be tightened securely before operating the fanLight Kit Adaptor Disassembly switch housing and end cap InstallationNO LIGHT KIT - Installation Switch Housing and Light Kit Adaptor Installation - NO LIGHT KIT Switch Housing and Light Kit Adaptor Installation - Continued NO LIGHT KITAdaptor Installation NO LIGHT KIT - END SCREW Figure #6LIGHT KIT - Installation Figure #9 Switch Housing and Light KitAdaptor Installation - Continued LIGHT KIT Figure #10 Figure #11Figure #12 Figure #14Figure #17 Figure #15Figure #16 W-84 WALL CONTROL INSTALLATION Prepare for W-84 Wall Control Bezel replacement as followsW-84 Wall control Preparation For use on product with BOTH UP and DOWN LIGHTS ONLYPrepare for W-84 Wall Control installation - Continued PINSRUBBER KEY PAD ALMONDW-84 Wall Control w-84 Control INSTALLATION Installing the W-84 Wall Controlsingle W-84 Installation NEUTRAL dual W-84 InstallationDIP SWITCHES Operation Power Make sure where you are in the sequence to the rightOperation Speed Control Operation Reversing Airflowchanging frequency setting To dim just the up lightTo dim just the down light NOTE All fans leave the factory set to “1111”Automatic Demonstration Program ++++Operation Safe-Exit and light-minder Program To enter the demonstration program+ + + Operation Home-Safe ProgramOperation Fan-Minder Program In the wall bezel replacement W-84 Wall Control Bezel replacement CONTINUED ALMOND WALL PLATE SCREWS ALMOND COLORED WALL PLATE BEZEL BEZEL TABS BEZEL ALIGNMENT PIN AND HOLEALMOND COLORED BEZEL Troubleshooting tips Product Specifications DimensionsWeight Care RecommendationsHolliston