Casablanca Fan Company SERIAL No. DJ06, MODEL # C31UxxZ, Holliston, Hanger Type

Page 4
Holliston®

PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!

Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to shipment. Before you begin to assemble and install your Casablanca fan, remove all parts from the carton and check them against the Parts Guide in this manual.

Make sure all parts are included in the box using the Parts Guide on the following pages.

If there are missing or broken parts:

Call 1-888-227-2178 Monday through Friday,7 a.m.to 4 p.m. PST.Your request will be handled immediately.Replacement parts will be sent to you via Federal Express.

Proper Parts Handling

Do not remove lightbulbs from their packaging until you are ready to install them.

Before discarding packaging materials, be certain that all parts have been removed.

Use a clean, dry paintbrush to remove small Styrofoam pieces that may remain after unpacking.

Do not brush Styrofoam into wiring cavities.

The blades in each pack are matched for equal weight to assure smooth fan operation.If more than one fan is being installed, do not mix blades from different cartons.

When cleaning,painting,or working near your fan,be cautious of the fan and blades.

RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!

Always turn power to the ceiling fan OFF before replacing lightbulbs or working on your fan.

Never insert anything into the path of the fan blades while the fan is in operation.

Never install a fan over a pool or spa.

Never operate a fan that has been damaged in any way.

Install the fan according to the instructions in this manual.

If the fan does not work:

Refer to the Troubleshooting Tips in this Owner’s Manual. Call Technical Support at 1-888-227-2178.

Contact your local Authorized Service Center.

Our Web site at www.casablancafanco.com contains additional information on Casablanca products, troubleshooting, and Authorized Dealer or Service Centers. Please do not return this product to the store.

Please take a moment to locate the model number and serial number from your fan (see below) and record this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already. These numbers are found on the motor identification plate affixed to the fan motor in the location shown below:

Motor Identification Plate

Holliston®

 

TYPE

HANGER TYPE

POMONA, CA DJ01 1151

MODEL #C31UxxZ

SERIAL No.: DJ06 2237

Serial Number

 

C31UxxZ TYPE Model Number

2

Image 4
Contents PN C3143001-AT0209 HollistonC31UxxZ O W N E R ’ S M A N U A LLIMITED WARRANTY Proof of PurchaseTHIS WARRANTY SUPERSEDES ALL HollistonPREVIOUS WARRANTIES CONTENTS HollistonRead and Save These Instructions PN C3143001 AT0608SERIAL No. DJ06 MODEL # C31UxxZHolliston TYPE7-Watt Incandescent Parts GuideUplight Bulbs Blade Iron Screws pre-installed, see pg 13, step 9a Adaptor AssemblySwitch Housing Cap Switch Housing Cap Screws 8-32 x 3/8For best performance and for your warranty to be valid use only genuine Casablanca blades, light fixtures, and accessoriesIntroduction Before You Start Safe Usesloped ceiling installations When to Use Extension PolesMOUNTING RECOMMENDATIONS General Guidelines Calculation of Ceiling AngleFan Installation Getting Started Ceiling plate InstallationInstalling a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet BoxCanopy Installation Lag Screw InstallationCANOPY LOCK WASHERS CANOPY SCREWS IMPORTANT SAFETY INFORMATION Prepare for fan installation as followsFan Preparation Figure #1 Figure #2Figure #4 Fan Preparation - continuedFigure #5 LIGHTBULB INSTALLATION uplight Install LightbulbsHanging the Fan Figure #6Canopy Electrical Connections Canopy Hatch and cover ring InstallationFigure #2 Blade Installation Blade InstallationAttach Blade Irons LIGHT FIXTURE Installation optional Blade Installation ContinuedBlade screws must be tightened securely before operating the fanNO LIGHT KIT - Installation switch housing and end cap InstallationLight Kit Adaptor Disassembly Switch Housing and Light Kit Adaptor Installation - NO LIGHT KIT Switch Housing and Light Kit Adaptor Installation - Continued NO LIGHT KITAdaptor Installation NO LIGHT KIT - END SCREW Figure #6LIGHT KIT - Installation Adaptor Installation - Continued LIGHT KIT Switch Housing and Light KitFigure #9 Figure #10 Figure #11Figure #12 Figure #14Figure #16 Figure #15Figure #17 W-84 WALL CONTROL INSTALLATION Prepare for W-84 Wall Control Bezel replacement as followsW-84 Wall control Preparation For use on product with BOTH UP and DOWN LIGHTS ONLYPrepare for W-84 Wall Control installation - Continued PINSRUBBER KEY PAD ALMONDsingle W-84 Installation w-84 Control INSTALLATION Installing the W-84 Wall ControlW-84 Wall Control DIP SWITCHES dual W-84 InstallationNEUTRAL Operation Power Make sure where you are in the sequence to the rightOperation Speed Control Operation Reversing Airflowchanging frequency setting To dim just the up lightTo dim just the down light NOTE All fans leave the factory set to “1111”Automatic Demonstration Program ++++Operation Safe-Exit and light-minder Program To enter the demonstration programOperation Fan-Minder Program Operation Home-Safe Program+ + + In the wall bezel replacement W-84 Wall Control Bezel replacement CONTINUED ALMOND COLORED BEZEL BEZEL BEZEL TABS BEZEL ALIGNMENT PIN AND HOLEALMOND WALL PLATE SCREWS ALMOND COLORED WALL PLATE Troubleshooting tips Product Specifications DimensionsWeight Care RecommendationsHolliston