Black & Decker CTL36 Transporting and Storage, OFF-SEASON Storage, Rbrc Seal Battery Recycling

Page 13
See ‘Tools-Elec-
tric’
– Yellow Pages –
for Service & Sales

TRANSPORTING AND STORAGE

 

 

DANGER: Rotating tines can cause serious injury. Release bail handle to turn tiller off and remove the safety

key before lifting, transporting or storing the tiller. Never pick up or carry the unit while the motor is running, serious

personal injury could result. Store in a dry place. Do not lift the tiller by the battery handles. Note: The tiller will not be

as heavy to lift if the battery pack is removed first. Do not use the latch as a lift point for the tiller.

 

OFF-SEASON STORAGE

 

1. In warmer climates to ensure optimal performance, it is recommended that the battery be maintained on constant

 

charge.

 

2. The tiller may be stored with the charger disconnected if all of the following conditions are met.

 

 

- the battery is fully charged before storing. (Failure to store fully charged will shorten battery life).

 

 

- the average temperatureof the storage location is below 50°F (10°C).

 

 

- storage duration is less than 6 months.

 

BATTERY SERVICE AND INSTALLATION

 

When service or repair is required, it is recommended that you take your tiller to an authorized Black & Decker

 

Service Center.

 

When servicing or replacing batteries, please note:

 

•

Use only the same type and size of battery as originally supplied.

 

•

Do not dispose of the batteries in a fire. The cell may explode. See Battery Recycling information below.

 

•

Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It

•

may be toxic if swallowed.

 

Exercise care in handling batteries in order not to short the battery with conducting materials such as rings,

 

 

bracelets, and keys. The battery or conductor may overheat and cause burns.

 

THE RBRC™ SEAL (BATTERY RECYCLING)

 

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lead acid battery (or battery pack)

 

indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already

 

been paid by Black & Decker. In some areas, it is illegal to place spent lead acid batteries in the trash or

 

municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.

Pb

RBRC in cooperation with Black & Decker and other battery users, has established programs in the

 

United States and Canada to facilitate the collection of spent lead acid batteries. Help protect our envi-

 

ronment and conserve natural resources by returning the lead acid battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call 1-800-544-6986.

ACCESSORIES

The CTL36 cordless tiller uses the RB-3612 battery. Recommended accessories for use with your tiller are available from your local dealer or authorized service center.

If you need assistance regarding accessories, please call:

WARNING:1-800-544-6986

The use of any accessory not recommended for use with this tool could be hazardous.

SERVICE INFORMATION

 

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable

power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black

& Decker location nearest you. Tofind your local service location, refer to the yellow page directory under "Tools—

Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The

defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased

(provided that the store is a participating retailer). Returns should be made within the time period of the retailerʼs policy

for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer

for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for

repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service

Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other

rights which vary from state to state or province to province. Should you have any questions, contact the manager of

your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call

1-800-544-6986for a free replacement.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,

check country specific warranty information contained in the packaging, call the local company or see the website for

warranty information.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents VEA EL Español EN LA Contraportada CTL36Removing Battery Training Safety Guidelines DefinitionsOperation Mended to till at a maximum depth of half the tine diameterWire Size AWG Maintenance and StorageFunctional Description Assembly Completing Garden Tiller Assembly Assembly InstructionsTools required for assembly MID Handle Assembly Figure CTinewassemblyrning Figure F Wheel Assembly Figure EDrag BAR ASSEMBLY- Figure G Battery LIFE. Refer to OFF-SEASON Storage Section Local Service Center orRemoving Battery from Tiller Figure H Charger Safety RulesCharging with Battery Removed from Tiller Charging PROCEDURE- Figures I, J, KWith the battery removed, insert Remove safety key I-1.charger plug J-1Operating Instructions This Switch Adjusting the Drag BAR Figure NFuture reference Charger receptacleUsing the Tiller Adjusting the Wheel Height Position Figure OCircuit Breaker Figure P Unjamming the Tines Figure QMaintena CE Problem RecommendationRbrc Seal Battery Recycling Battery Service and InstallationAccessories Service InformationMode D’EMPLOI Table DES Matières Débloquage des dentsConsignes DE Sécurité Importantes Lignes Directrices EN Matièrede Sécurité DéfinitionsFormation FonctionnementEntretien ET Entreposage Calibre minimal recommandé pour les rallongesConserver CES Consignes Longueur totale de la rallongePage Description Fonctionnelle Montage Désemballage Figure BMontage DE LA Poignée Centrale Figure C Montage DE LA Poignée Supérieure Figure DEnfiler une rondelle E-1à chaque extrémité de lʼessieu Montage DES Roues Figure EMontage DE Dents Figure F Avertissement les dents dʼun rotoculteur sont tranchantesRègles DE Sécurité Pour LE Chargeur Dépose DU BLOC-PILES DU Rotoculteur Figure HNETTOYAGE.22 Charger LE BLOC-PILES Laissé Dans LE Procédure DE Charge Figures I, J, KRotoculteur Charger LE BLOC-PILES Déposé DUDʼaccéder à la prise du chargeur Mode dʼemploi pour un usage ultérieurEntreposé Fonctionnement DE CET InterrupteurUtilisation DU Rotoculteur Réglage DE LA Hauteur DES Roues Figure ODisjoncteur Figure P Débloquage DES Dents Figure QProblème Recommandation Renseignement concernant les accessoires, composer le Entretien ET Installationdu BLOC-PILESTransport ET Entreposage Entreposage Hors Saison800 Commercial.si les étiquettes dʼavertissement deviennentManual DE Instrucciones Índice Ensamblaje de la barra de arrastreInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESPuedeAVISOprovocar daños en la propiedad CapacitaciónConserve Estas Instrucciones Mantenimiento Y AlmacenamientoLongitud total del cable Calibre AWG del tamaño del conductorPage Descripción DE LAS Funciones Herramientas que se necesitan para el ensamblaje Desembalaje Figura BEnsamblaje DEL Mango Intermedio Figura C Ensamblaje DEL Mango Superior Figura DColoque una arandela E-1en cada extremo del eje Ensamblaje DE LAS Ruedas Figura EEnsamblaje DE LOS Dientes Figura F Ensamblaje DE LA Barra DE Arrastre Figura GUtilice Únicamente Baterías DE Repuesto Aprobadas POR Instrucciones DE CargaExtracción DE LA Batería DE LA Motoazada Figura H Normas DE Seguridad Para EL CargadorMotoazada seguridad Carga CON LA Bateríainstalada EN LAAjustes. Conserve este manual para futuras consultas Conozca LA Motoazadainstrucciones DE OperaciónReceptáculo del cargador Ajustepeligrode LA Barra DE Arrastre Figura NUSO DE LA Motoazada Ajuste DE LA Posición DE Altura DE LAS Ruedas Figura ODisyuntor Figura P Desatascamiento DE LOS Dientes Figura QProblema Recomendación Almacenamiento DE LA Unidad Fuera DE Temporada Transporte Y AlmacenamientoMantenimiento E Instalación DE LA Batería Solamente Para Propositos DE Mexico Años DE Garantia Telephone · No. TeléfonoEsta Garantia no Aplica Cuando

CTL36 specifications

The Black & Decker CTL36 is a versatile and powerful cordless tool designed to enhance efficiency and ease of use for both professional tradespeople and DIY enthusiasts. This tool epitomizes reliability and innovation, catering to a variety of applications from heavy-duty tasks to delicate work.

One of the standout features of the CTL36 is its robust 36V Lithium-Ion battery. This battery technology not only ensures longer run times but also provides fade-free power throughout its use. Unlike traditional battery systems that may lose strength as they drain, the Lithium-Ion technology of the CTL36 maintains consistent performance, allowing users to complete their tasks without interruptions.

The CTL36 is equipped with an efficient brushless motor. Brushless motors are known for their durability and efficiency, offering greater torque and longer motor life compared to brushed counterparts. This means that users can expect higher performance levels and less maintenance over time, increasing productivity on job sites.

Another notable characteristic of the CTL36 is its ergonomic design. It features a lightweight and compact structure that allows for easy handling and maneuverability. The rubber grip on the handle further enhances comfort, reducing fatigue during prolonged use. This is particularly important for professionals who rely on their tools day in and day out.

The tool is also designed with a range of features that enhance its versatility. It includes adjustable speed settings, allowing users to switch between high speed for fast cutting and low speed for more control in intricate tasks. Additionally, the CTL36 comes with an LED work light, providing illumination in darker spaces, thereby ensuring safety and accuracy.

Safety features are also integrated into the design, with an electric brake that halts the tool's operation instantly when the trigger is released, minimizing the risk of accidents. This is a critical feature in busy work environments where safety is paramount.

In conclusion, the Black & Decker CTL36 is a well-rounded cordless tool that combines advanced technologies such as Lithium-Ion battery and brushless motor with user-friendly features like adjustable speed and ergonomic design. Perfect for a wide range of applications, it signifies Black & Decker's commitment to delivering high-quality, reliable products that meet the demands of modern users. Whether you are a seasoned professional or an enthusiastic DIYer, the CTL36 offers the performance and versatility needed to tackle any project with confidence.
Top Page Image Contents