Black & Decker CTL36 Local Service Center or, Battery LIFE. Refer to OFF-SEASON Storage Section

Page 8

BATTERY

CHARGING INSTRUCTIONS

 

USE ONLY BLACK & DECKER APPROVED REPLACEMENT BATTERIES - CONTACT YOUR

 

AUTION:

LOCAL SERVICE CENTER OR 1-800-544-6986.

 

The battery is a 36-volt sealed lead acid system. There is no liquid contained within the battery and the tiller/battery

can therefore be stored in any position without fear of leakage.

 

IT IS RECOMMENDED THAT THE BATTERY BE RECHARGED AFTER USE TO PROLONG THE BATTERY LIFE.

FREQUENT CHARGING WILL NOT HARM YOUR BATTERY,AND WILL ENSURE THAT THE BATTERY IS FULLY

CHARGED AND READY FOR ITS NEXT USE. STORING BATTERY NOT FULLY CHARGED WILL SHORTEN

BATTERY LIFE. REFER TO OFF-SEASON STORAGE SECTION.

 

•

For optimal performance the battery should be kept on constant charge when not in use.

•

The battery should be charged in its proper orientation.

 

•

The battery should be charged in a cool dry place.

 

•

The battery does not need to be fully discharged before recharging.

 

•

2 to 3 initial charging cycles may be required after purchase to achieve maximum run time capacity.

•

A fully charged battery can be safely stored down to -40°C (-40°F).

 

•

The battery is maintenance free.

 

•

The CTL36 cordless tiller uses the RB-3612 battery. The battery should not be used for any other purpose.

REMOVING BATTERY FROM TILLER - FIGURE H

 

Prior to removing battery, place tiller on level ground.

H

Release bail handle to turn tiller off, wait for tines to stop, and remove

safety key.

 

 

1.

To remove the battery H-3, lift the lever H-1, and then rotate back

 

2.

away from battery to unlatch clasp H-2.

 

Remove the battery from the tiller by grasping the handle areas on both

3

3.

sides of the top of the battery and lift straight up.

Prior to the installation of the battery, ensure that the tiller is clear of de-

 

 

bris and the charger plug is disconnected from the battery.

 

CHARGER SAFETY RULES

1. Plug charger directly into an electrical outlet. DO NOT ABUSE THE CORD. Never carry charger by cord. Do not disconnect the charger from the outlet, tiller or battery by pulling it by the cord.

2. WARNING: To reduce the risk of fire, electrical shock, or personal injury do not attempt to use this charger with any other product. Likewise, do not attempt to charge the battery with any other charger.

3. Do not service tiller with charger, safety key or battery pack installed.

4. Do not operate a damaged charger. Replace damaged cords or charger immediately at an authorized Black & Decker service center.

5. Always charge the battery in a dry area protected from the weather. Do not expose the tiller, battery or charger to rain. Do not charge in wet locations. Do not charge battery when temperature is above 104°F (40°C) or below 41°F (5°C). Remove battery and charge indoors if above or below these temperatures. Charge the battery in a well ventilated location.

6. Keep the tiller, battery and charger away from water, heat sources, (such as radiators, heaters, stoves, etc.) flames, or chemicals. Be careful not to damage the charger cord, by keeping cord away from sharp edges.

7. Prior to reinstalling the battery into the tiller, disconnect charger plug from battery, or damage may occur.

WARNING: FIRE HAZARD

ALWAYSDISCONNECT THE CHARGER FROM THE POWER SUPPLY (WALL OUTLET) BEFORE REMOVING THE CHARGER CONNECTOR. UNDER CERTAIN CONDITIONS, WITH THE CHARGER PLUGGED IN TO THE POWER SUPPLY, THE EXPOSED CONNECTOR CAN BE SHORTED BY FOREIGN MATERIAL AND MAY CAUSE A FIRE. FOREIGN MATERIALS OF A CONDUCTIVE NATURE, SUCH AS, BUT NOT LIMITED TO, STEEL WOOL, ALUMINUM FOIL, OR ANY BUILD-UP OF METALLIC PARTICLES, SHOULD BE KEPT FROM THE CONNECTOR. ALWAYSUNPLUG CHARGER BEFORE ATTEMPTING TO CLEAN.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CTL36 VEA EL Español EN LA ContraportadaRemoving Battery Safety Guidelines Definitions TrainingOperation Mended to till at a maximum depth of half the tine diameterMaintenance and Storage Wire Size AWGFunctional Description Assembly Instructions Assembly Completing Garden Tiller AssemblyTools required for assembly MID Handle Assembly Figure CDrag BAR ASSEMBLY- Figure G Wheel Assembly Figure ETinewassemblyrning Figure F Local Service Center or Battery LIFE. Refer to OFF-SEASON Storage SectionRemoving Battery from Tiller Figure H Charger Safety RulesCharging PROCEDURE- Figures I, J, K Charging with Battery Removed from TillerWith the battery removed, insert Remove safety key I-1.charger plug J-1This Switch Adjusting the Drag BAR Figure N Operating InstructionsFuture reference Charger receptacleAdjusting the Wheel Height Position Figure O Using the TillerCircuit Breaker Figure P Unjamming the Tines Figure QProblem Recommendation Maintena CEBattery Service and Installation Rbrc Seal Battery RecyclingAccessories Service InformationMode D’EMPLOI Débloquage des dents Table DES MatièresLignes Directrices EN Matièrede Sécurité Définitions Consignes DE Sécurité ImportantesFormation FonctionnementCalibre minimal recommandé pour les rallonges Entretien ET EntreposageConserver CES Consignes Longueur totale de la rallongePage Description Fonctionnelle Désemballage Figure B MontageMontage DE LA Poignée Centrale Figure C Montage DE LA Poignée Supérieure Figure DMontage DES Roues Figure E Enfiler une rondelle E-1à chaque extrémité de lʼessieuMontage DE Dents Figure F Avertissement les dents dʼun rotoculteur sont tranchantesNETTOYAGE.22 Dépose DU BLOC-PILES DU Rotoculteur Figure HRègles DE Sécurité Pour LE Chargeur Procédure DE Charge Figures I, J, K Charger LE BLOC-PILES Laissé Dans LERotoculteur Charger LE BLOC-PILES Déposé DUMode dʼemploi pour un usage ultérieur Dʼaccéder à la prise du chargeurEntreposé Fonctionnement DE CET InterrupteurRéglage DE LA Hauteur DES Roues Figure O Utilisation DU RotoculteurDisjoncteur Figure P Débloquage DES Dents Figure QProblème Recommandation Entretien ET Installationdu BLOC-PILES Renseignement concernant les accessoires, composer leTransport ET Entreposage Entreposage Hors SaisonCommercial.si les étiquettes dʼavertissement deviennent 800Manual DE Instrucciones Ensamblaje de la barra de arrastre ÍndicePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesPuedeAVISOprovocar daños en la propiedad CapacitaciónMantenimiento Y Almacenamiento Conserve Estas InstruccionesLongitud total del cable Calibre AWG del tamaño del conductorPage Descripción DE LAS Funciones Desembalaje Figura B Herramientas que se necesitan para el ensamblajeEnsamblaje DEL Mango Intermedio Figura C Ensamblaje DEL Mango Superior Figura DEnsamblaje DE LAS Ruedas Figura E Coloque una arandela E-1en cada extremo del ejeEnsamblaje DE LOS Dientes Figura F Ensamblaje DE LA Barra DE Arrastre Figura GInstrucciones DE Carga Utilice Únicamente Baterías DE Repuesto Aprobadas PORExtracción DE LA Batería DE LA Motoazada Figura H Normas DE Seguridad Para EL CargadorCarga CON LA Bateríainstalada EN LA Motoazada seguridadConozca LA Motoazadainstrucciones DE Operación Ajustes. Conserve este manual para futuras consultasReceptáculo del cargador Ajustepeligrode LA Barra DE Arrastre Figura NAjuste DE LA Posición DE Altura DE LAS Ruedas Figura O USO DE LA MotoazadaDisyuntor Figura P Desatascamiento DE LOS Dientes Figura QProblema Recomendación Mantenimiento E Instalación DE LA Batería Transporte Y AlmacenamientoAlmacenamiento DE LA Unidad Fuera DE Temporada Solamente Para Propositos DE Mexico Esta Garantia no Aplica Cuando Telephone · No. TeléfonoAños DE Garantia

CTL36 specifications

The Black & Decker CTL36 is a versatile and powerful cordless tool designed to enhance efficiency and ease of use for both professional tradespeople and DIY enthusiasts. This tool epitomizes reliability and innovation, catering to a variety of applications from heavy-duty tasks to delicate work.

One of the standout features of the CTL36 is its robust 36V Lithium-Ion battery. This battery technology not only ensures longer run times but also provides fade-free power throughout its use. Unlike traditional battery systems that may lose strength as they drain, the Lithium-Ion technology of the CTL36 maintains consistent performance, allowing users to complete their tasks without interruptions.

The CTL36 is equipped with an efficient brushless motor. Brushless motors are known for their durability and efficiency, offering greater torque and longer motor life compared to brushed counterparts. This means that users can expect higher performance levels and less maintenance over time, increasing productivity on job sites.

Another notable characteristic of the CTL36 is its ergonomic design. It features a lightweight and compact structure that allows for easy handling and maneuverability. The rubber grip on the handle further enhances comfort, reducing fatigue during prolonged use. This is particularly important for professionals who rely on their tools day in and day out.

The tool is also designed with a range of features that enhance its versatility. It includes adjustable speed settings, allowing users to switch between high speed for fast cutting and low speed for more control in intricate tasks. Additionally, the CTL36 comes with an LED work light, providing illumination in darker spaces, thereby ensuring safety and accuracy.

Safety features are also integrated into the design, with an electric brake that halts the tool's operation instantly when the trigger is released, minimizing the risk of accidents. This is a critical feature in busy work environments where safety is paramount.

In conclusion, the Black & Decker CTL36 is a well-rounded cordless tool that combines advanced technologies such as Lithium-Ion battery and brushless motor with user-friendly features like adjustable speed and ergonomic design. Perfect for a wide range of applications, it signifies Black & Decker's commitment to delivering high-quality, reliable products that meet the demands of modern users. Whether you are a seasoned professional or an enthusiastic DIYer, the CTL36 offers the performance and versatility needed to tackle any project with confidence.
Top Page Image Contents