Alamo 7191852C manual Safety

Page 10
(SG-1)

SAFETY

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety Messages before assembling, operating or servicing this Implement. This equipment should only be operated by those persons who have read the manual, who are responsible and trained, and who know how to do so responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this manual and on decals which are attached to the equipment. The Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word are intended to warn the owner/operator of impending hazards and the degree of possible injury faced when operating this equipment.

Practice all usual and customary safe working precautions and above all---remember safety is up to YOU. Only YOU can prevent serious injury or death from unsafe practices.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards. (SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3)

PA91 03/09

Safety Section 1-2

© 2009 Alamo Group Inc.

Image 10
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Operator Safety Instructions and Practices Wait a minute...Save a lifeSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Tractor Preparation Fitting Operator GuardBallast Weight John Deere Conversion KIT 81- 30Attachment to Tractor DeliverySi Model Ti Model Assembly Fitting Control Unit in CAB Tank OIL RequirementsGearbox PA91 Ti Running UP ProcedurePA91 Si Removal from Tractor StorageProper Torque Values for Fasteners Operation Section Operation Standard Specifications Head SpecificationsOperator Requirements Personal Protective Equipment PPERops and Seat Belt Tractor RequirementsOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor Horsepower Tractor Safety DevicesTractor Ballast 3-Point Hitch Front End WeightHydraulics Power Take Off PTO Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Connecting Mower Head HydraulicsPA91 02/08 Operation Section PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Machine Controls Operating the Boom MowerEngaging Drive Tractor Position Wire TrapForward Speed Operating SpeedHedge Cutting Procedure Upward CuttingReversing Rotation Si Only Lift Float Kit Optional Machine Configuration Flail TypesDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating the Tractor and Implement Operating InstructionsSGM-08 Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO Operating Speed and Ground Speed Operating the MowerSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting the Tractor and Implement Transporting on Public RoadwaysOperation Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralFloat KIT Accumulator Test Filtration MaintenanceHydraulic System Oil SupplyHydraulic Pumps FlailheadCable Operated Armhead Control Valve Replacing Damaged or Worn Spool O RingsMain Relief Valve CablesNon-Return Valve Angling Arm Ram Seal Replacement General InformationHydraulic Rams Reach RamHydraulic Motor Rotor Control VALVE/RELIEF ValveO. Gearbox Relief ValveHydraulic Hoses Hose ReplacementHose Warranty Replacing Shaft SealsALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A