Alamo 7191852C manual Shutting Down the Attached Head

Page 90
(SG-9)

OPERATION

OPERATION

9.7 Shutting Down the Attached Head

To shut down attached mower head, first bring the tractor to a complete stop. Decrease engine RPM to idle then disengage cutterhead. The mower head will come to a complete stop within a suitable amount of time. Do not engage or disengage the cutterheads at a high RPM unless there is an emergency situation.

Park the tractor on a level surface, place the transmission in park or neutral and apply the parking brake, shut down the engine, remove the key, and wait for all motion to come to a complete stop before exiting the tractor. OPS-B- 0011_F

ON-OFF Switch

BEFORE leaving the tractor seat, always engage the brake and/or set the tractor transmission in parking gear, disengage the PTO, stop the engine, remove the key, and wait for all moving parts to stop. Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling. Never dismount a Tractor that is moving or while the engine is running. Operate the Tractor controls from the tractor seat only.

PA91 02/08

Operation Section 4-38

© 2009 Alamo Group Inc.

Image 90
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Operator Safety Instructions and Practices Wait a minute...Save a lifeSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Tractor Preparation Fitting Operator GuardBallast Weight John Deere Conversion KIT 81- 30Delivery Attachment to TractorSi Model Ti Model Assembly Fitting Control Unit in CAB OIL Requirements TankGearbox Running UP Procedure PA91 TiPA91 Si Removal from Tractor StorageProper Torque Values for Fasteners Operation Section Operation Standard Specifications Head SpecificationsOperator Requirements Personal Protective Equipment PPETractor Requirements Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor Safety Devices Tractor HorsepowerTractor Ballast Front End Weight 3-Point HitchHydraulics Power Take Off PTO Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Connecting Mower Head HydraulicsPA91 02/08 Operation Section PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Operating the Boom Mower Machine ControlsEngaging Drive Tractor Position Wire TrapForward Speed Operating SpeedHedge Cutting Procedure Upward CuttingReversing Rotation Si Only Lift Float Kit Optional Machine Configuration Flail TypesDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating the Tractor and Implement Operating InstructionsSGM-08 Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO Operating Speed and Ground Speed Operating the MowerSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting the Tractor and Implement Transporting on Public RoadwaysOperation Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralFloat KIT Accumulator Test Filtration MaintenanceHydraulic System Oil SupplyHydraulic Pumps FlailheadCable Operated Armhead Control Valve Replacing Damaged or Worn Spool O RingsCables Main Relief ValveNon-Return Valve Angling Arm Ram Seal Replacement General InformationHydraulic Rams Reach RamHydraulic Motor Rotor Control VALVE/RELIEF ValveO. Gearbox Relief ValveHydraulic Hoses Hose ReplacementHose Warranty Replacing Shaft SealsALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A