Alamo 7191852C manual SGM-08

Page 89
(SGM-11)

OPERATION

There are obvious and hidden potential hazards in the operation of this Mower. REMEMBER! This machine is often operated in heavy brush and in heavy weeds. The Blades of this Mower can throw objects if shields are not properly installed and maintained. Serious injury or even death may occur unless care is taken to insure the safety of the operator, bystanders, or passersby in the area. Do not operate this machine with anyone in the immediate area. Stop mowing if anyone is within 100 yards of mower. (SGM-02)

Do not mow with two machines in the same area except with Cab tractors with the windows closed.

Mow only in conditions where you have clear visibility in daylight or with adequate artificial lighting. Never mow in darkness or foggy conditions where you cannot clearly see at least 100 yards(90 m) in front and to the sides of the tractor and mower. Make sure that you can clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead obstructions, power lines, debris and foreign objects. If you are unable to clearly see these type of items discontinue mowing. (SGM-1)

Avoid mowing in reverse direction when possible. Check to make sure there are no persons behind the mower and use extreme care when mowing in reverse. Mow only at a slow ground speed where you can safely operate and control the tractor and mower. Never mow an area that you have not inspected and removed debris or foreign material.

(SGM-08)

Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and repairing the Mower and Tractor:

-Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust.

-Do Not smoke or have an open flame near the Mower and Tractor.

-Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes. Periodically shut down the Tractor and Mower and clean clippings and collected debris from the mower deck. (SGM-12)

PA91 02/08

Operation Section 4-37

© 2009 Alamo Group Inc.

OPERATION

Image 89
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Wait a minute...Save a life Operator Safety Instructions and PracticesSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Fitting Operator Guard Tractor PreparationJohn Deere Conversion KIT 81- 30 Ballast WeightSi Model DeliveryAttachment to Tractor Ti Model Assembly Fitting Control Unit in CAB Gearbox OIL RequirementsTank PA91 Si Running UP ProcedurePA91 Ti Storage Removal from TractorProper Torque Values for Fasteners Operation Section Operation Head Specifications Standard SpecificationsPersonal Protective Equipment PPE Operator RequirementsOperator Thrown Object Protection Tractor RequirementsRops and Seat Belt Tractor Lighting and SMV Emblem Tractor Ballast Tractor Safety DevicesTractor Horsepower Hydraulics Front End Weight3-Point Hitch Getting on and OFF the Tractor Power Take Off PTODismounting the Tractor Boarding the TractorStarting the Tractor Connecting Mower Head Hydraulics Connecting Attaching Head to the BoomPA91 02/08 Operation Section Tractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Engaging Drive Operating the Boom MowerMachine Controls Forward Speed Wire TrapTractor Position Operating SpeedUpward Cutting Hedge Cutting ProcedureReversing Rotation Si Only Lift Float Kit Optional Flail Types Machine ConfigurationDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating Instructions Operating the Tractor and ImplementSGM-08 Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower Operating Speed and Ground SpeedSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting on Public Roadways Transporting the Tractor and ImplementOperation Operation Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideOperation Operation Maintenance Section General LubricationHydraulic System Filtration MaintenanceFloat KIT Accumulator Test Oil SupplyFlailhead Hydraulic PumpsReplacing Damaged or Worn Spool O Rings Cable Operated Armhead Control ValveNon-Return Valve CablesMain Relief Valve Hydraulic Rams Ram Seal Replacement General InformationAngling Arm Reach RamO. Gearbox Rotor Control VALVE/RELIEF ValveHydraulic Motor Relief ValveHose Warranty Hose ReplacementHydraulic Hoses Replacing Shaft SealsALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A