Alamo 7191852C manual Safety

Page 18
(SGM-15)

SAFETY

SAFETY

Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and repairing the Mower and Tractor:

-Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust.

-Do Not smoke or have an open flame near the Mower and Tractor.

-Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes. Periodically shut down the Tractor and Mower and clean clippings and collected debris from the mower deck. (SGM-12)

The Mower is designed for certain mowing applications and is rated to cut up to a specific size vegetation (see Mower Standard Equipment and Specifications). DO NOT use this mower to cut vegetation above the Mower’s rated capacity or to cut any type of non- vegetative material. Only operate this Mower on a properly sized and equipped Tractor. Operating this Mower in an application for which it is not designed and/or operating the Mower with the wrong size Tractor can cause Mower component damage and equipment failure resulting in possible serious injury or death. (SGM-14)

Do not operate or pull the mower into standing water. When uplift or fan type mower blades contact water they can be severely deflected downward causing possible failure of blade resulting in serious boldly injury to the operator or bystanders.

Use extreme caution when raising the Mower above ground level. Stop the Blades from turning when the Mower is raised and passersby are within 100 yards. Raising the Mower exposes the Cutting Blades which creates a potentially serious hazard and can cause serious injury by objects thrown from the Blades or by contact with the Blades. (SPU-1)

PA91 03/09

Safety Section 1-10

© 2009 Alamo Group Inc.

Image 18
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Operator Safety Instructions and Practices Wait a minute...Save a lifeSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Tractor Preparation Fitting Operator GuardBallast Weight John Deere Conversion KIT 81- 30Delivery Attachment to TractorSi Model Ti Model Assembly Fitting Control Unit in CAB OIL Requirements TankGearbox Running UP Procedure PA91 TiPA91 Si Removal from Tractor StorageProper Torque Values for Fasteners Operation Section Operation Standard Specifications Head SpecificationsOperator Requirements Personal Protective Equipment PPETractor Requirements Rops and Seat BeltOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor Safety Devices Tractor HorsepowerTractor Ballast Front End Weight 3-Point HitchHydraulics Power Take Off PTO Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Connecting Mower Head HydraulicsPA91 02/08 Operation Section PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Operating the Boom Mower Machine ControlsEngaging Drive Tractor Position Wire TrapForward Speed Operating SpeedHedge Cutting Procedure Upward CuttingReversing Rotation Si Only Lift Float Kit Optional Machine Configuration Flail TypesDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating the Tractor and Implement Operating InstructionsSGM-08 Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO Operating Speed and Ground Speed Operating the MowerSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting the Tractor and Implement Transporting on Public RoadwaysOperation Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralFloat KIT Accumulator Test Filtration MaintenanceHydraulic System Oil SupplyHydraulic Pumps FlailheadCable Operated Armhead Control Valve Replacing Damaged or Worn Spool O RingsCables Main Relief ValveNon-Return Valve Angling Arm Ram Seal Replacement General InformationHydraulic Rams Reach RamHydraulic Motor Rotor Control VALVE/RELIEF ValveO. Gearbox Relief ValveHydraulic Hoses Hose ReplacementHose Warranty Replacing Shaft SealsALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A