Alamo 7191852C manual Driving the Tractor and Boom

Page 83

OPERATION

8.4 Driving the Tractor and Boom

 

Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the

 

tractor. Never operate the tractor at speeds that cannot be safely handled or which will prevent the operator

 

from stopping quickly during an emergency. If the power steering or engine ceases operating, stop the tractor

 

immediately as the tractor will be difficult to control.

 

Perform turns with the tractor and mower at slow

 

 

 

 

 

speeds to determine how the tractor with and

 

 

 

attached implement handles a turn. Determine the

 

 

 

 

safe speed to maintain proper control of the tractor

 

 

OPERATION

when making turns. When turning with the

 

 

 

 

 

implement the overall working length and width of

 

 

 

the unit is increased. Allow additional clearance for

 

 

 

the unit when turning or when passing large

 

 

 

obstructions.

 

 

 

 

To avoid overturns, drive the tractor with care and

 

 

 

 

 

 

 

at safe speeds, especially when operating over

 

 

 

rough ground, crossing ditches or slopes, and

 

 

 

turning corners. Use extreme caution when

 

 

 

operating on steep slopes. Keep the tractor in a low

 

 

 

gear when going downhill. DO NOT coast or free-

 

 

 

wheel downhill.

 

 

 

 

OPS-B- 0006

 

 

 

 

 

 

 

 

 

 

Never Leave the mower unattended while the head is in the raised

 

 

position. The mower could fall causing serious injury to anyone who

 

 

might inadvertently be under the mower. (SBM-4)

 

 

Always keep a careful lookout and use extreme care when working

 

 

around overhead obstructions. Never allow the Mower head or boom

 

 

within 10 feet of any power line. When working close to overhead

 

 

power lines consult your electric company for a safe code of operation.

 

 

(SBM-7)

 

PA91 02/08

Operation Section 4-31

 

 

 

 

 

 

© 2009 Alamo Group Inc.

Image 83
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Wait a minute...Save a life Operator Safety Instructions and PracticesSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Fitting Operator Guard Tractor PreparationJohn Deere Conversion KIT 81- 30 Ballast WeightSi Model DeliveryAttachment to Tractor Ti Model Assembly Fitting Control Unit in CAB Gearbox OIL RequirementsTank PA91 Si Running UP ProcedurePA91 Ti Storage Removal from TractorProper Torque Values for Fasteners Operation Section Operation Head Specifications Standard SpecificationsPersonal Protective Equipment PPE Operator RequirementsOperator Thrown Object Protection Tractor RequirementsRops and Seat Belt Tractor Lighting and SMV Emblem Tractor Ballast Tractor Safety DevicesTractor Horsepower Hydraulics Front End Weight3-Point Hitch Getting on and OFF the Tractor Power Take Off PTODismounting the Tractor Boarding the TractorStarting the Tractor Connecting Mower Head Hydraulics Connecting Attaching Head to the BoomPA91 02/08 Operation Section Tractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Engaging Drive Operating the Boom MowerMachine Controls Operating Speed Wire TrapForward Speed Tractor PositionUpward Cutting Hedge Cutting ProcedureReversing Rotation Si Only Lift Float Kit Optional Flail Types Machine ConfigurationDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating Instructions Operating the Tractor and ImplementSGM-08 Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower Operating Speed and Ground SpeedSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting on Public Roadways Transporting the Tractor and ImplementOperation Operation Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideOperation Operation Maintenance Section General LubricationOil Supply Filtration MaintenanceHydraulic System Float KIT Accumulator TestFlailhead Hydraulic PumpsReplacing Damaged or Worn Spool O Rings Cable Operated Armhead Control ValveNon-Return Valve CablesMain Relief Valve Reach Ram Ram Seal Replacement General InformationHydraulic Rams Angling ArmRelief Valve Rotor Control VALVE/RELIEF ValveO. Gearbox Hydraulic MotorReplacing Shaft Seals Hose ReplacementHose Warranty Hydraulic HosesALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A