Alamo 7191852C manual Maintenance and Service Safety Instructions and Practices

Page 22
(SG-20)
(SG-14)
(SG-8)
(S3PT-11)
(STI-10)

SAFETY

SAFETY

Your driving vision may be reduced or impaired by the tractor, cab, or implement. Before driving on public roadways identify any limited vision areas, and make adjustments to your operating position, mirrors, and the implement transport position so that you can clearly see the area where you will be traveling, and any traffic that may approach you. Failure to maintain adequate vision of the public roadway and traffic can result in serious injury or even death.

Maintenance and Service Safety Instructions and Practices

Make sure the PTO shield, integral driveline shields, and input shields are is installed when using PTO-driven equipment. Always replace any shield if it is damaged or missing. (S3PT-8)

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Implement on the ground or securely blocked up, disengage the PTO, and turn off the tractor engine. Push and pull the Remote Cylinder lever in and out several times prior to starting any maintenance or repair work. (S3PT-09)

Always disconnect the main PTO Driveline from the Tractor before performing service on the Implement. Never work on the Implement with the tractor PTO driveline connected and running. Rotating Parts, Blades or Drivelines could turn without warning and cause immedi- ate entanglement, injury or death.

Always maintain the safety signs in good readable condition. If the safety signs are missing, damaged, or unreadable, obtain and install replacement safety signs immediately. (SG-5)

Do not modify or alter this Implement. Do not permit anyone to modify or alter this Implement, any of its components or any Implement function.

Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death.

Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running.

PA91 03/09

Safety Section 1-14

© 2009 Alamo Group Inc.

Image 22
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Operator Safety Instructions and Practices Wait a minute...Save a lifeSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Tractor Preparation Fitting Operator GuardBallast Weight John Deere Conversion KIT 81- 30Attachment to Tractor DeliverySi Model Ti Model Assembly Fitting Control Unit in CAB Tank OIL RequirementsGearbox PA91 Ti Running UP ProcedurePA91 Si Removal from Tractor StorageProper Torque Values for Fasteners Operation Section Operation Standard Specifications Head SpecificationsOperator Requirements Personal Protective Equipment PPERops and Seat Belt Tractor RequirementsOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor Horsepower Tractor Safety DevicesTractor Ballast 3-Point Hitch Front End WeightHydraulics Power Take Off PTO Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Connecting Mower Head HydraulicsPA91 02/08 Operation Section PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Machine Controls Operating the Boom MowerEngaging Drive Tractor Position Wire TrapForward Speed Operating SpeedHedge Cutting Procedure Upward CuttingReversing Rotation Si Only Lift Float Kit Optional Machine Configuration Flail TypesDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating the Tractor and Implement Operating InstructionsSGM-08 Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO Operating Speed and Ground Speed Operating the MowerSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting the Tractor and Implement Transporting on Public RoadwaysOperation Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralFloat KIT Accumulator Test Filtration MaintenanceHydraulic System Oil SupplyHydraulic Pumps FlailheadCable Operated Armhead Control Valve Replacing Damaged or Worn Spool O RingsMain Relief Valve CablesNon-Return Valve Angling Arm Ram Seal Replacement General InformationHydraulic Rams Reach RamHydraulic Motor Rotor Control VALVE/RELIEF ValveO. Gearbox Relief ValveHydraulic Hoses Hose ReplacementHose Warranty Replacing Shaft SealsALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A