Alamo 7191852C manual Boarding the Tractor, Dismounting the Tractor

Page 62

OPERATION

OPERATION

4.1 Boarding the Tractor

Use both hands and equipped handrails and steps for support when boarding the tractor. Never use control levers for support when mounting the tractor. Seat yourself in the operator’s seat and secure the seat belt around you.

Never allow passengers to ride on the tractor or attached equipment. Riders can easily fall off and be seriously injured or killed from falling off and being ran over. It is the operator’s responsibility to forbid all extra riders at all times. OPS-U- 0008

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death. (SG-10)

Never allow children to operate or ride on the Power Unit or Implement.

(SPU-17)

4.2 Dismounting the Tractor

Before dismounting, park the tractor and implement on a reasonably level surface, apply the parking brake, idle the engine down, disengage the PTO, and lower the implement to the ground. Shut down the tractor engine according to the operator’s manual, remove the key, and wait for all motion to completely stop. Never leave the seat until the tractor, its engine and all moving parts have come to a complete stop.

Use hand rails and steps when exiting the tractor. Be careful of your step and use extra caution when mud, ice, snow or other matter has accumulated on the steps or hand rails. Use all handrails and steps for support and never rush or jump off the tractor. OPS-U- 0009

BEFORE leaving the tractor seat, always engage the brake and/or set the tractor transmission in parking gear, disengage the PTO, stop the engine, remove the key, and wait for all moving parts to stop. Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling. Never dismount a Tractor that is moving or while the engine is running. Operate the Tractor controls from the tractor seat only. (SG-9)

PA91 02/08

Operation Section 4-10

© 2009 Alamo Group Inc.

Image 62
Contents PA91 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Maintenance Section Cables Hydraulic Rams Page Safety Section Safety Operator Safety Instructions and Practices Wait a minute...Save a lifeSafety Equipment Operation Safety Instructions and Practices Safety Safety Safety SGM-06 Safety Stop Mowing if Passersby are Within 100 Yards Unless Transporting Safety Instructions and Practices Safety Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Decal Location QTY Level Description Decal Description Safety Safety Safety PA91 03/09 Safety Section Safety Safety Alamo Industrial Logo Alamo Name Logo Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Tractor Preparation Fitting Operator GuardBallast Weight John Deere Conversion KIT 81- 30Si Model DeliveryAttachment to Tractor Ti Model Assembly Fitting Control Unit in CAB Gearbox OIL RequirementsTank PA91 Si Running UP ProcedurePA91 Ti Removal from Tractor StorageProper Torque Values for Fasteners Operation Section Operation Standard Specifications Head SpecificationsOperator Requirements Personal Protective Equipment PPEOperator Thrown Object Protection Tractor RequirementsRops and Seat Belt Tractor Lighting and SMV Emblem Tractor Ballast Tractor Safety DevicesTractor Horsepower Hydraulics Front End Weight3-Point Hitch Power Take Off PTO Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Connecting Attaching Head to the Boom Connecting Mower Head HydraulicsPA91 02/08 Operation Section PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBoom Unit Pre-Operation Inspection and Service OPS-B- 0023E Hydraulic PUMP/OIL Reservoir Flail Head Inspection Do not Operate an Unsafe Tractor or Mower Tractor PRE-OPERATION Inspection Engaging Drive Operating the Boom MowerMachine Controls Tractor Position Wire TrapForward Speed Operating SpeedHedge Cutting Procedure Upward CuttingReversing Rotation Si Only Lift Float Kit Optional Machine Configuration Flail TypesDriving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Transport Position Driving the Tractor and Boom Operating the Tractor and Implement Operating InstructionsSGM-08 Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO Operating Speed and Ground Speed Operating the MowerSGM-08 Shutting Down the Attached Head TRACTOR, BOOM, and Attached Head Storage Transporting the Tractor and Implement Transporting on Public RoadwaysOperation Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Lubrication GeneralFloat KIT Accumulator Test Filtration MaintenanceHydraulic System Oil SupplyHydraulic Pumps FlailheadCable Operated Armhead Control Valve Replacing Damaged or Worn Spool O RingsNon-Return Valve CablesMain Relief Valve Angling Arm Ram Seal Replacement General InformationHydraulic Rams Reach RamHydraulic Motor Rotor Control VALVE/RELIEF ValveO. Gearbox Relief ValveHydraulic Hoses Hose ReplacementHose Warranty Replacing Shaft SealsALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER PA91-SOM-02/08 7191852C Printed U.S.A