Exmark FMD 604, FMD 524 manual Motion Control Linkage Adjustment, Seat Switch Adjustment

Page 37

MOTION CONTROL LINKAGE ADJUSTMENT

FIGURE 12

MOTION CONTROL LINKAGE ADJUSTMENT

6.2.11Seat Switch Adjustment

a)Stop engine, wait for all moving parts to stop, and remove key.

b)With operator out of seat, adjust the seat switch to provide a 1/16” clearance between the switch plunger and the seat frame (See Figure 13).

c)To adjust, loosen the top nut securing the seat switch to the seat rail weldment. Adjust the bottom nut until the 1/16” between plunger and seat frame has been obtained. Tighten the top nut. Recheck the measurement and adjust again if necessary.

d)Check safety interlock system as outlined in 6.1.5.

FIGURE 13

SEAT SWITCH ADJUSTMENT

6.2.12Electric Clutch Adjustment

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Engage parking brake.

c)Place .015-.021 inch feeler gauge through each of the three clutch gap holes. If gap exceeds this range, tighten the three adjusting nuts (c) until the proper gap is obtained (See Figure 14). The three clutch gap holes are located at the “nut side” of the adjusting bolts. The adjusting bolts can be identified by the springs surrounding each bolt.

( c )

FIGURE 14

ELECTRIC CLUTCH ADJUSTMENT

- 32 -

Image 37

Contents Serial Nos. 440,000 & Higher For Turf Ranger Serial Nos. 440,000 & Higher and FMD524 & FMD604Page EFFECTIVE DATE September 1 Program EXMARK PARTS PLUS PROGRAMHow the Program Works OPERATORS MANUAL SAFETY TABLE OF CONTENTSSPECIFICATIONS ASSEMBLY INSTRUCTIONS1.1 SAFETY ALERT SYMBOL 1.SAFETYATTENTION! BECOME ALERT YOUR SAFETY IS INVOLVED 1.2 TRAININGDANGER DANGER 1.4 OPERATION G0083 SAFE ZONE FOR MOWINGa Before refueling b Before making height adjustments a Before checking, cleaning, or working on the mowerc When parking inside a building c Disconnect battery cables in the reverse order after starting1.5 MAINTENANCE AND STORAGE 1.6 SAFETY SIGNS LOCATION Under Belt Shields PART NO. 103-2248 LOCATION Steering ConsoleLOCATION LH & RH Front Top Surface of Mower Deck LOCATION On Intake Screen Below Fuel Tank2.1 MODEL NUMBER TR23KC 2.2 ENGINE 2. SPECIFICATIONS2.3 FUEL SYSTEM 2.4 ELECTRICAL SYSTEM2.8 TIRES 2.10 DIMENSIONS2.9 MOWER DECK 2.11 TORQUE REQUIREMENTS3.1 Uncrate tractor and mower deck 3.2 SERVICE BATTERY 3. ASSEMBLY INSTRUCTIONSThe machine is shipped with a filled lead acid battery 3.4 INSTALL REAR STEERING WHEEL 3.3 INSTALL SEAT3.5 INSTALL DRIVE WHEELS 3.6 INSTALL HANDLE BARHARDWARE AND SUPPORT PIN LOCATION FOR DECK SUPPORT FRAME IDLER PULLEY KIT AND LOCATION 4. CONTROLS3.9 POSITION DISCHARGE CHUTE NOTE Do Not tow machine or transmission damage may result 5.1 PRE-START 5. OPERATION INSTRUCTIONS5.2 MOWING DRIVE WHEEL RELEASE LEVER5.3 TRANSPORTING 6.1 PERIODIC MAINTENANCE 6. MAINTENANCE & ADJUSTMENTSClean all debris from around the engine and transmission daily 6.1.2 Clean engine air cooling system6.1.3 Clean transmission cooling compartment Service Interval Daily 6.1.4 Clean grass build-up under mower deck and check mower bladesDO NOT USE WRENCH HERE BLADE BOLT INSTALLATION6.1.7 Service air cleaner Service Interval 50 hrs 6.1.6 Check for loose hardware Service Interval Dailyb Loosen retaining clips and remove air cleaner compartment cover More often under severe conditions6.1.10 Check tire pressures Service Interval 40 hrs 6.1.9 Check hydraulic oil level Service Interval 40 hrsb Inflate tires to pressures specified in Section 2.8 Specifications 6.1.11 Check battery charge Service Interval MonthlySERVICE LUBRICATION CHARTCASTER WHEEL ASSEMBLY FITTING LOCATIONS6.1.16 Change fuel filter Service Interval As Required 6.1.15 Remove engine shrouds and clean cooling fins6.1.17 Lubrication of steering yoke pivot Service Interval Monthly 6.1.18 Check spark plugs Service Interval 160 hrs6.1.20 Inspect Electric clutch gap Service Interval 250 hrs 6.1.19.2 Change hydraulic oil Service Interval YearlyRefer to Section 6.2.12 for inspection and adjustment procedures 6.1.22 Wheel hub, slotted nut torque specification6.2 ADJUSTMENTS ANTI-SCALP ROLLER BOLT INSTALLATION ANTI-SCALP ROLLER AND CUTTING HEIGHT ADJUSTMENTTorque to 40-45 ft-lbs. 54-61 N-m, or loss of roller may result 6.2.3 Mower deck drive belt No adjustment necessaryPage PARKING BRAKE QUADRANT ADJUSTMENT NEUTRAL CENTERING DEVICE ADJUSTMENTBRAKE CONTROL LINK AND SPRING ADJUSTMENT PARKING BRAKE NEUTRAL LOCKOUT ADJUSTMENT SEAT SWITCH ADJUSTMENT MOTION CONTROL LINKAGE ADJUSTMENTELECTRIC CLUTCH ADJUSTMENT THROTTLE TENSION ARMREST ADJUSTMENTArmrest Adjustment Tab Rotate ¼ Turn 7.2 BATTERY DISPOSAL 8. TROUBLE SHOOTING7. WASTE DISPOSAL 7.1 MOTOR OIL DISPOSALENGINE TROUBLESHOOTING TABLE ENGINE TROUBLESHOOTINGPROBLEM Engine Deck Wiring Diagram 9. WIRING DIAGRAMSConsole Wiring Diagram 10.Limited Warranty Exmark Turf Equipment Page LAZER Z MICRO-MULCH ACCESSORYLAZER Z HP LAZER Z XP