Exmark Diesel manual Pre-Start, Operating Instructions, Raise the Rollover Protection System Rops

Page 19

Operation

The buzzer is a warning signal that the engine is overheating or the oil pressure is low. See the Troubleshooting section.

Pre-Start

Fill fuel tank. For best results use only clean, fresh diesel fuel, with a cetane rating of 40 higher

Note: Do Not use kerosene or gasoline instead of diesel fuel. Failure to observe this caution will damage the engine.

Do Not add oil to fuel.

Do Not overfill fuel tank. Never fill the fuel tank so that the fuel level rises above a level that is 1/2 inch (13 mm) below the bottom of the filler neck to allow for fuel expansion and prevent fuel spillage.

Make sure you understand the controls, their locations, their functions, and their safety requirements.

Refer to the Maintenance section and perform all the necessary inspection and maintenance steps.

Figure 5

1.

Roll bar

3.

Pin

2.

Raised position

4.

Hairpin cotter pin

 

 

 

 

Operating Instructions

Raise the Rollover Protection System (ROPS)

Important: Lower the roll bar only when absolutely necessary.

1.Remove the hairpin cotter pins and remove the two roll bar pins (Figure 5).

2.Raise the roll bar to the upright position and install the two pins and secure them with the hairpin cotter pins (Figure 5).

Important: Always use the seat belt with the roll bar in the raised position. Ensure that the rear part of the seat is secured with the seat latch.

Starting the Engine

1.Move the motion control levers out to the neutral lock position.

2.Pull up and back on the parking brake lever to engage the parking brake.

3.Push in on the PTO switch to the “STOP” position.

Note: It is not necessary for the operator to be in the seat to start the engine.

4.On a warm engine, place the throttle in the “SLOW” position.

5.On a cold engine, (below 14°F (-10°C)), place the throttle in the “MIDWAY” position.

Note: Do Not use fuel left over from summer.

6.Turn ignition switch to the “ON” position. Depress the glow plug switch and the glow plug light will turn on. Hold switch as required by chart below. Turn the ignition switch to the “START” position. Release the ignition switch as soon as the engine starts.

19

Image 19
Contents Frontrunnertm California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesOperation Slope Operation Using the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 103-1636 103-5881 103-7218 107-2102 107-2112 109-2355 109-2356 109-7949 19426-87881 109-2698 Model Numbers SpecificationsSystems Tires & Wheels Hydrostatic Ground Drive SystemCutting Deck Torque Requirements DimensionsOperation Product OverviewControls Coolant Temperature Light PTO Engagement SwitchHydraulic Lift Switch Coolant Temperature GaugeStarting the Engine Pre-StartOperating Instructions Raise the Rollover Protection System RopsDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineTransporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Coolant Level Check Engine Oil LevelChange Engine Coolant Check Battery ChargeEngine must initiate shutdown Check Safety Interlock SystemCheck for Loose Hardware Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltCheck Condition Of Belts Check Hydraulic Oil LevelCheck Auxiliary Hydraulic Oil Level Check Tire PressuresLubricate Rear Caster Wheel Hubs Lubricate Grease FittingsLubricate Motion Control Shaft Lubricate Brake Handle PivotLubricate Brake Rod Bushings Lubricate Motion Control Bronze BushingsChange Hydraulic System Filter Lubricate Steering Linkage Rod EndsChange Fuel Filter Drain Water from Fuel TankDielectric Grease Fuel Tank Mounting Hardware SpecificationsCheck Wheel Hub Locknuts Thread Locking AdhesivesAlternator Belt Tension Pump Drive Belt ReplacementPark Brake Adjustment Pump Drive Belt TensionMotion Control Linkage Adjustment Weight Transfer Spring Adjustment Reverse Indicator AdjustmentRight-Hand Side of Unit Shown Rear Caster Pivot Bearings Pre-Load AdjustmentMotor Oil Disposal Clean Engine Cooling SystemBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories