Exmark Diesel manual Reverse Indicator Adjustment, Weight Transfer Spring Adjustment

Page 35

Maintenance

Figure 17

1.Loosen jam nut

2.Pump control rod linkage

3.Use wrench to turn double nuts

9.Move the motion control levers to the reverse position. Return the motion control levers to neutral. The wheels must stop turning (or slightly creep in reverse).

10.Stop engine and wait for all moving parts to stop. Remove jumper wire from wire harness connector and plug connector into seat switch.

11.Lower from jackstands.

Reverse Indicator

Adjustment

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Tilt seat forward.

3.Begin with either the left or right motion control lever. Move lever to the neutral position and pull lever back until the clevis pin (on arm below pivot shaft) contacts the end of the slot (just beginning to put pressure on spring), (see Figure 18).

Figure 18

1.

Motion control lever

4.

Loosen here

2.

End of slot

5.

Turn bolt here

3.Yoke

4.Check where lever is relative to notch in neutral plate (should be centered allowing lever to pivot outward to the neutral lock position).

5.If adjustment is needed, loosen the nut against the yoke and while applying slight rearward pressure on the motion control lever, turn the head of the adjustment bolt in the appropriate direction until lever is centered (keeping rearward pressure on the lever will keep the pin at the end of the slot and allow the adjustment bolt to move the lever to the appropriate position). Tighten lock nut.

6.Repeat on opposite side of unit.

Weight Transfer Spring Adjustment

Weight transfer springs are assembled from the factory to apply the maximum amount of weight onto the drive wheels. This setting provides the greatest amount of traction. Some conditions may require the rear wheel lift to be reduced. This can be done by reducing the amount to weight transfer, which will increase the amount of weight on the front and rear casters.

1.Rotate the left motion control arm up and into the operation position.

2.Locate and loosen the knob under the rear of the left fender (see Figure 19).

35

Image 35
Contents Frontrunnertm California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesOperation Slope Operation Using the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 103-1636 103-5881 103-7218 107-2102 107-2112 109-2355 109-2356 109-7949 19426-87881 109-2698 Systems SpecificationsModel Numbers Cutting Deck Hydrostatic Ground Drive SystemTires & Wheels Torque Requirements DimensionsControls Product OverviewOperation Coolant Temperature Light PTO Engagement SwitchHydraulic Lift Switch Coolant Temperature GaugeStarting the Engine Pre-StartOperating Instructions Raise the Rollover Protection System RopsDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineTransporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Coolant Level Check Engine Oil LevelChange Engine Coolant Check Battery ChargeEngine must initiate shutdown Check Safety Interlock SystemCheck for Loose Hardware Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltCheck Condition Of Belts Check Hydraulic Oil LevelCheck Auxiliary Hydraulic Oil Level Check Tire PressuresLubricate Rear Caster Wheel Hubs Lubricate Grease FittingsLubricate Motion Control Shaft Lubricate Brake Handle PivotLubricate Brake Rod Bushings Lubricate Motion Control Bronze BushingsChange Hydraulic System Filter Lubricate Steering Linkage Rod EndsChange Fuel Filter Drain Water from Fuel TankDielectric Grease Fuel Tank Mounting Hardware SpecificationsCheck Wheel Hub Locknuts Thread Locking AdhesivesAlternator Belt Tension Pump Drive Belt ReplacementPark Brake Adjustment Pump Drive Belt TensionMotion Control Linkage Adjustment Weight Transfer Spring Adjustment Reverse Indicator AdjustmentRight-Hand Side of Unit Shown Rear Caster Pivot Bearings Pre-Load AdjustmentMotor Oil Disposal Clean Engine Cooling SystemBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Page See EXMARK’S Complete Line of Accessories