Husqvarna 39765, 13 Bio, 11 Bio manual Presentation, Location of the controls

Page 10

PRESENTATION

Presentation

Congratulation on your choice of a first-class quality product.

This manual describes four models that are fitted with engines from Briggs & Stratton of 10.5 and 12.5 horsepower respectively.

Rider 11 and Rider 11 Bio has an in-line gearbox with five forward gears and one reverse gear.

On the Rider 13 and Rider 13 Bio the power trans- mission from the engine is handled by a hydrostatic gearbox which enables stepless variation of the speed.

6

5

4

3

13

2

1

7

8

9

10

11

12

Location of the controls

1.Ignition lock

2.Throttle/Choke lever

3.Adjustment of cutting height

4.Lifting lever, cutting unit

5.Speed control for reversing (only on 13 and 13 Bio)

6.Speed limiter for driving forwards on 13 and 13 Bio

Parking brake on 11 and 11 Bio

7.Parking brake on 13 and 13 Bio Clutch pedal on 11 and 11 Bio

8.Lock button for parking brake (left side on 13 and 13 Bio, right side on 11 and 11 Bio)

9.Seat adjustment

10.Fuel tank cap

11.Main lock (under seat)

12.Lever for disengagement of drive (only on 13 and 13 Bio)

13.Gear lever on 11 and 11 Bio

English – 9

Image 10

Contents Rider 11/13 Rider 11 Bio/13 Bio 101 91Contents Travel and transport on public roads InstructionDear customer TowingSerial number Safety InstructionsGood service Engine TransmissionExplanation of Symbols These instructions are for your safety. Read them carefully General useDriving on slopes Do as followsMaintenance ChildrenBattery can explode and cause severe injuries Presentation PresentationLocation of the controls Clutch pedal Presentation Rider 11 / 11 BIOThrottle and Choke lever Brake pedal / Parking brakeSpeed limiter Presentation Rider 13/13 BIOParking brake Lift lever for cutting unit Cutting unitRider 11 Bio and Rider 13 Bio have a twin-blade Seat Lever for adjustment of cutting heightFuelling Before starting DrivingStarting the engine Cold engine Warm engineFor Rider 13 and Rider 13 Bio Driving the machineFor Rider 11 and Rider 11 Bio Cutting tips Stopping the engine Hill start, manual gearboxRelease lever Rider 13 and Rider 13 Bio Maintenance schedule MaintenanceDaily Maintenance interval Hours Nance 100 Front hood Rider 11 and Rider Dismantling of the machine hoodsEngine hood Front hood Rider 11 Bio and Rider 13 BioRight-hand fender Left-hand fenderChecking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Adjusting the brake Rider 11 and Rider 11 BioCheck and adjust the brakes on Rider 13 and Rider 13 Bio Checking the brake Rider 11 and Rider 11 BioChecking and adjustment of the throttle wire Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Inspecting the safety system Checking the tyre pressure Check the engine’s cooling air intakeChecking the cutting unit’s parallelism Maintenance Service position for BioClip Maintenance Rider 11 BIO/13 BIOPlacing in service position Maintenance Rider 11 BIO/13 BIO Restoring from service position Checking the blades Replacing the break-pin BioClipCheck the engine’s oil level LubricationChanging the oil Lubrication of belt tensioner General lubricationLubrication Rider 11 and Rider 11 Bio Lubrication of front wheel bearingsTrouble Shooting Schedule Problem ProcedureStorage ServiceWinter storage Engine Technical DataDimensions Rider Electrical systemDimensions Rider 11 Bio Rider 13 Bio EU declaration of conformity Only applies to Europe Pre-delivery service Servicejournal Rider 11/13Work done Date, mileage, stamp, sign Servicejournal Page 2000W50