Husqvarna 13 Bio, 39765, 11 Bio manual Explanation of Symbols

Page 5

EXPLANATION OF SYMBOLS

These symbols are on the machine and in the operator’s manual.

Study them carefully so that you know what they mean.

Read the operator’s manual

R N

Reverse

Neutral

Fast

Slow

Engine off

Battery

Choke

Fuel

Oil pressure

Cutting height

Backwards

Forwards

Ignition

Hydrostatic free wheel

Use eye and	Clutch in	Clutch out	Parking brake	Brake	Clutch	Warning
hearing protection

Soundlevel	Warning!	Warning!	Never drive across a slope	European standard for
	Rotating blades.	Risk that the machine can tip over		machine safety

Never use the machine if persons,	Never carry passengers on the
especially children, or animals,	machine or equipment.
are in the vicinity.

Starting instructions Read the instructions Check the engine’s oil level Check the hydrostat’s oil level Lift up the cutting unit

Put the gear shift/hydrostat pedal in neutral

Brake

If the engine is cold use the choke Start the engine

Release the parking brake before driving

Keep hands and feet away	Drive very slowly
from under the hood when	without the cutting unit.

the engine is running.

Speed limiter pedal forwards

Neutral

Speed limiter pedal reverse

Switch off the engine and take off the ignition cable before repairs or maintenance

4 – English

Image 5

Contents 101 91 Rider 11/13 Rider 11 Bio/13 BioContents Dear customer InstructionTravel and transport on public roads TowingGood service Safety InstructionsSerial number Engine TransmissionExplanation of Symbols General use These instructions are for your safety. Read them carefullyDo as follows Driving on slopesChildren MaintenanceBattery can explode and cause severe injuries Location of the controls PresentationPresentation Throttle and Choke lever Presentation Rider 11 / 11 BIOClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13/13 BIOSpeed limiter Rider 11 Bio and Rider 13 Bio have a twin-blade Cutting unitLift lever for cutting unit Fuelling Lever for adjustment of cutting heightSeat Starting the engine DrivingBefore starting Warm engine Cold engineFor Rider 11 and Rider 11 Bio Driving the machineFor Rider 13 and Rider 13 Bio Cutting tips Release lever Rider 13 and Rider 13 Bio Hill start, manual gearboxStopping the engine Daily Maintenance interval Hours Nance 100 MaintenanceMaintenance schedule Engine hood Dismantling of the machine hoodsFront hood Rider 11 and Rider Front hood Rider 11 Bio and Rider 13 BioLeft-hand fender Right-hand fenderChecking and adjustment of the steering wires Check and adjust the brakes on Rider 13 and Rider 13 Bio Adjusting the brake Rider 11 and Rider 11 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioReplacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureChecking the cutting unit’s parallelism Maintenance Placing in service position Maintenance Rider 11 BIO/13 BIOService position for BioClip Maintenance Rider 11 BIO/13 BIO Restoring from service position Replacing the break-pin BioClip Checking the bladesChanging the oil LubricationCheck the engine’s oil level General lubrication Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioProblem Procedure Trouble Shooting ScheduleWinter storage ServiceStorage Dimensions Rider Technical DataEngine Electrical systemDimensions Rider 11 Bio Rider 13 Bio EU declaration of conformity Only applies to Europe Work done Date, mileage, stamp, sign Servicejournal Rider 11/13Pre-delivery service Servicejournal Page 2000W50