Husqvarna 39765, 13 Bio manual Checking the brake Rider 11 and Rider 11 Bio

Page 24

MAINTENANCE

Checking the brake Rider 11 and Rider 11 Bio

The brake is of the disc brake type and is fitted on the gearbox.

Check that the brake is correctly adjusted by measuring the distance between the brake lever and the front edge of the recess on the chassis. The distance should be 0–1 mm when the brake is not applied.

Adjusting the brake Rider 11 and Rider 11 Bio

1.Release the lock nuts (1).

2.Tension the wire with the adjusting screw (2) so that the distance between the brake lever and the front edge of the recess on the chassis is 1 mm.

3.Tighten the lock nuts (1) after adjustment.

2	1
1

Check and adjust the brakes on Rider 13 and Rider 13 Bio

Check that the brakes are correctly adjusted by placing the rider mower on a shallow downhill slope and applying the brake.

If the rider mower begins to move then the brakes must be adjusted.

The brake is adjusted as follows:

1.Release the lock nuts (1).

2.Tension the wire with the adjusting screw (2) until all the play in the wire is taken up.

3.Tighten the lock nuts (1).

4.On completion of the adjustment the brake should be re-checked.

WARNING!

Poorly adjusted brakes can result in reduced braking power.

	2
1	1

English – 23

Image 24

Contents Rider 11/13 Rider 11 Bio/13 Bio 101 91Contents Instruction Dear customerTravel and transport on public roads TowingSafety Instructions Good serviceSerial number Engine TransmissionExplanation of Symbols These instructions are for your safety. Read them carefully General useDriving on slopes Do as followsMaintenance ChildrenBattery can explode and cause severe injuries Presentation PresentationLocation of the controls Presentation Rider 11 / 11 BIO Throttle and Choke leverClutch pedal Brake pedal / Parking brakePresentation Rider 13/13 BIO Speed limiterParking brake Cutting unit Lift lever for cutting unitRider 11 Bio and Rider 13 Bio have a twin-blade Lever for adjustment of cutting height SeatFuelling Driving Before startingStarting the engine Cold engine Warm engineDriving the machine For Rider 13 and Rider 13 BioFor Rider 11 and Rider 11 Bio Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 and Rider 13 Bio Maintenance Maintenance scheduleDaily Maintenance interval Hours Nance 100 Dismantling of the machine hoods Engine hoodFront hood Rider 11 and Rider Front hood Rider 11 Bio and Rider 13 BioRight-hand fender Left-hand fenderChecking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 Bio Check and adjust the brakes on Rider 13 and Rider 13 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioChecking and adjustment of the throttle wire Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterCheck the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Inspecting the safety system Checking the tyre pressure Check the engine’s cooling air intakeChecking the cutting unit’s parallelism Maintenance Maintenance Rider 11 BIO/13 BIO Service position for BioClipPlacing in service position Maintenance Rider 11 BIO/13 BIO Restoring from service position Checking the blades Replacing the break-pin BioClipLubrication Check the engine’s oil levelChanging the oil Lubrication of belt tensioner General lubricationLubrication Rider 11 and Rider 11 Bio Lubrication of front wheel bearingsTrouble Shooting Schedule Problem ProcedureService StorageWinter storage Technical Data Dimensions RiderEngine Electrical systemDimensions Rider 11 Bio Rider 13 Bio EU declaration of conformity Only applies to Europe Servicejournal Rider 11/13 Pre-delivery serviceWork done Date, mileage, stamp, sign Servicejournal Page 2000W50