Husqvarna 39765, 13 Bio, 11 Bio manual Servicejournal Rider 11/13, Pre-delivery service

Page 44

		SERVICEJOURNAL RIDER 11/13

	Work done		Date, mileage, stamp, sign
	Pre-delivery service
	1.	Top up battery with acid and recharge for four hours.
	2.	Fit steering wheel, seat and any optional equipment.
	3.	Adjust cutting unit:
		Adjust the lifting springs (the “weight” of the cutting unit should
		be 12-15 kg). Only applies to BioClip.
		Adjust cutting unit so that rear edge is about 2–4 mm higher
		than front edge.
		Adjust cutting unit height setting so that cutting height limit is 5
		mm above the frame of the unit at the lowest cutting height.
	4.	Check that engine has correct amount of oil.

5.Check that the right amount of oil is in the transmission. (Not Rider 11)

6. Check and adjust tyre pressure (60 kPa, 0.6 bar).
7. Connect battery.
8. Fill with fuel and start engine.
9. Check that machine does not move in neutral. (Not Rider 11)
10. Check:
Forward drive.
Reverse drive.
Operation of blades.
Seat safety switch.
Lift lever safety switch.
Safety switch for hydrostatic pedals/neutral setting.
11. Check engine revs 2 950 rpm.
12. Tell customer about:	Pre-delivery service carried out.
Need and benefits of following the service schedule.	No outstanding problems.
Need and benefits of following the service schedule.
The need and advantages of leaving the machine for regular	Certified:
The need and advantages of leaving the machine for regular
service.
The effects of maintenance on the machine’s second hand
value.
Range of applications for BioClip.
13. Complete proof of sale, etc.

After first 5 hours 1. Change engine oil.

English – 43

Image 44

Contents Rider 11/13 Rider 11 Bio/13 Bio 101 91Contents Instruction Dear customerTravel and transport on public roads TowingSafety Instructions Good serviceSerial number Engine TransmissionExplanation of Symbols These instructions are for your safety. Read them carefully General useDriving on slopes Do as followsMaintenance ChildrenBattery can explode and cause severe injuries Location of the controls PresentationPresentation Presentation Rider 11 / 11 BIO Throttle and Choke leverClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13/13 BIOSpeed limiter Rider 11 Bio and Rider 13 Bio have a twin-blade Cutting unitLift lever for cutting unit Fuelling Lever for adjustment of cutting heightSeat Starting the engine DrivingBefore starting Cold engine Warm engineFor Rider 11 and Rider 11 Bio Driving the machineFor Rider 13 and Rider 13 Bio Cutting tips Release lever Rider 13 and Rider 13 Bio Hill start, manual gearboxStopping the engine Daily Maintenance interval Hours Nance 100 MaintenanceMaintenance schedule Dismantling of the machine hoods Engine hoodFront hood Rider 11 and Rider Front hood Rider 11 Bio and Rider 13 BioRight-hand fender Left-hand fenderChecking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 Bio Check and adjust the brakes on Rider 13 and Rider 13 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioChecking and adjustment of the throttle wire Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Checking the tyre pressure Check the engine’s cooling air intakeChecking the cutting unit’s parallelism Maintenance Placing in service position Maintenance Rider 11 BIO/13 BIOService position for BioClip Maintenance Rider 11 BIO/13 BIO Restoring from service position Checking the blades Replacing the break-pin BioClipChanging the oil LubricationCheck the engine’s oil level Lubrication of belt tensioner General lubricationLubrication Rider 11 and Rider 11 Bio Lubrication of front wheel bearingsTrouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage Technical Data Dimensions RiderEngine Electrical systemDimensions Rider 11 Bio Rider 13 Bio EU declaration of conformity Only applies to Europe Work done Date, mileage, stamp, sign Servicejournal Rider 11/13Pre-delivery service Servicejournal Page 2000W50