Husqvarna Driving the machine, For Rider 13 and Rider 13 Bio, For Rider 11 and Rider 11 Bio

Page 17

DRIVING

7.When the engine has started release the ignition key to neutral position.

Push the throttle control to the required speed. For cutting 3/4 to full throttle.

WARNING!

Never run the engine indoors, in enclosed or poorly ventilated areas. The exhaust fumes contain toxic carbon monoxide.

STOP START

Driving the machine

1.Release the parking brake by pressing down the brake pedal.

2.For Rider 13 and Rider 13 Bio

Carefully press down one of the pedals until the correct speed is reached.

To drive forwards: press down pedal (1).

To reverse: press down pedal (2).

For Rider 11 and Rider 11 Bio

Press the clutch and engage the required gear. To engage reverse gear the lock button must be pressed down.

•Gears 1–4 are used for mowing.

•Gears 4–5 are used for transport.

Starting is possible irrespective of which gear is engaged.

IMPORTANT INFORMATION

Do not change gear from forward drive to reverse while the machine is moving.

The clutch must be used for each gear change.

Stop the machine before changing for forward drive to reverse, otherwise the gearbox can be damaged.

Never use force to engage a gear. If a gear will not engage directly release and push down the clutch again, and then try to engage the gear again.

16 – English

Rider 13

2

1

Rider 13

N

Rider 11

Image 17

Contents 101 91 Rider 11/13 Rider 11 Bio/13 BioContents Dear customer InstructionTravel and transport on public roads TowingGood service Safety InstructionsSerial number Engine TransmissionExplanation of Symbols General use These instructions are for your safety. Read them carefullyDo as follows Driving on slopesChildren MaintenanceBattery can explode and cause severe injuries Location of the controls PresentationPresentation Throttle and Choke lever Presentation Rider 11 / 11 BIOClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13/13 BIOSpeed limiter Rider 11 Bio and Rider 13 Bio have a twin-blade Cutting unitLift lever for cutting unit Fuelling Lever for adjustment of cutting heightSeat Starting the engine DrivingBefore starting Warm engine Cold engineFor Rider 11 and Rider 11 Bio Driving the machineFor Rider 13 and Rider 13 Bio Cutting tips Release lever Rider 13 and Rider 13 Bio Hill start, manual gearboxStopping the engine Daily Maintenance interval Hours Nance 100 MaintenanceMaintenance schedule Engine hood Dismantling of the machine hoodsFront hood Rider 11 and Rider Front hood Rider 11 Bio and Rider 13 BioLeft-hand fender Right-hand fenderChecking and adjustment of the steering wires Check and adjust the brakes on Rider 13 and Rider 13 Bio Adjusting the brake Rider 11 and Rider 11 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioReplacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureChecking the cutting unit’s parallelism Maintenance Placing in service position Maintenance Rider 11 BIO/13 BIOService position for BioClip Maintenance Rider 11 BIO/13 BIO Restoring from service position Replacing the break-pin BioClip Checking the bladesChanging the oil LubricationCheck the engine’s oil level General lubrication Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioProblem Procedure Trouble Shooting ScheduleWinter storage ServiceStorage Dimensions Rider Technical DataEngine Electrical systemDimensions Rider 11 Bio Rider 13 Bio EU declaration of conformity Only applies to Europe Work done Date, mileage, stamp, sign Servicejournal Rider 11/13Pre-delivery service Servicejournal Page 2000W50