Husqvarna 13 Bio, 39765, 11 Bio manual Lubrication of belt tensioner, General lubrication

Page 37

LUBRICATION

Check the transmission’s oil level

Rider 13 and Rider 13 Bio

1.Lift off the transmission cover. Release the two screws (one of each side) and lift off the trans- mission cover.

2.Check that there is oil in the transmission oil tank. Top up if necessary with engine oil SAE 10W/30 (class SF–CC).

Lubrication of belt tensioner

The belt tensioner must be lubricated regularly with high-quality molybdenum sulphide grease*.

Inject grease into the nipple on the right side below the engine bottom pulley until grease is forced out.

With daily use lubrication should be conducted twice a week.

General lubrication

All joints and bearings are lubricated on manufac- ture with molybdenum sulphide grease. Re-grease with same type of grease*. Lubricate the steering and control wires with engine oil.

The machine should be lubricated regularly, and twice a week when used daily.

*Grease from well-known brand names (petrol companies, etc.) usually maintains a good quality. The most important property is that the grease provides good protection against corrosion.

36 – English

Image 37

Contents 101 91 Rider 11/13 Rider 11 Bio/13 BioContents Dear customer InstructionTravel and transport on public roads TowingGood service Safety InstructionsSerial number Engine TransmissionExplanation of Symbols General use These instructions are for your safety. Read them carefullyDo as follows Driving on slopesChildren MaintenanceBattery can explode and cause severe injuries Presentation PresentationLocation of the controls Throttle and Choke lever Presentation Rider 11 / 11 BIOClutch pedal Brake pedal / Parking brakeSpeed limiter Presentation Rider 13/13 BIOParking brake Lift lever for cutting unit Cutting unitRider 11 Bio and Rider 13 Bio have a twin-blade Seat Lever for adjustment of cutting heightFuelling Before starting DrivingStarting the engine Warm engine Cold engineFor Rider 13 and Rider 13 Bio Driving the machineFor Rider 11 and Rider 11 Bio Cutting tips Stopping the engine Hill start, manual gearboxRelease lever Rider 13 and Rider 13 Bio Maintenance schedule MaintenanceDaily Maintenance interval Hours Nance 100 Engine hood Dismantling of the machine hoodsFront hood Rider 11 and Rider Front hood Rider 11 Bio and Rider 13 BioLeft-hand fender Right-hand fenderChecking and adjustment of the steering wires Check and adjust the brakes on Rider 13 and Rider 13 Bio Adjusting the brake Rider 11 and Rider 11 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioReplacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Inspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureChecking the cutting unit’s parallelism Maintenance Service position for BioClip Maintenance Rider 11 BIO/13 BIOPlacing in service position Maintenance Rider 11 BIO/13 BIO Restoring from service position Replacing the break-pin BioClip Checking the bladesCheck the engine’s oil level LubricationChanging the oil General lubrication Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage Dimensions Rider Technical DataEngine Electrical systemDimensions Rider 11 Bio Rider 13 Bio EU declaration of conformity Only applies to Europe Pre-delivery service Servicejournal Rider 11/13Work done Date, mileage, stamp, sign Servicejournal Page 2000W50