Tabletop Mounting | 3Com 6200 specs

Tabletop Mounting

Installation

Tabletop Mounting

The system can be mounted on any desk or table top. To do this you first need to attach the four rubber feet, supplied with the system, to the bottom of the box. To do this, complete the following:

1.Turn the system over onto its top with the bottom facing up.

2.Locate the indented feet locators, as shown in the following figure.

Place rubber feet here.

3.Peel backing off of the rubber feet and press them down firmly on the indents.

Once the rubber feet are installed you can mount the system on a solid flat surface.

2-6	3COM Security Switch 6200 Hardware and Software Users Guide

Image 18

3Com manual Tabletop Mounting, 3COM Security Switch 6200 Hardware and Software Users Guide

Contents

10/100/1000 Security Switch Hardware and Software Users Guides10/100 FIBER End of Life Statement UNITED STATES GOVERNMENT LEGENDENVIRONMENTAL STATEMENT Regulated Materials Statement 3COM Security Switch 6200 Hardware and Software Users Guide ContentsInstallation About this Guide 5 Upgrading the System Software 4 Configuring the Security Switch 6200 SystemTechnical Specifications Technical Support Safety Connector Pin AssignmentsRegulatory Information Regulatory Standards Compliance 3COM Security Switch 6200 Hardware and Software Users Guide Audience About this GuideIntended Conventions Install Server Installation and Configuration Guide 3COM Security Switch 6200 Hardware and Software Users GuideSecurity Switch 6200 Product Release Notes Security Switch 6200 Applications Guide Introduction SystemComponents Chassis Figure 1-1 6200 Front ViewFigure 1-2 Rear Panel Component Layout Configuration Tool Management OptionsFirst Time Startup Interview 3COM Security Switch 6200 Hardware and Software Users Guide Installation Before You Start Site Requirements RequirementDescription 10/100 Figure 2-1 3COM Security Switch 6200 Shipping ContentsMGMT1 MGMT2 SYS HDD FIBER Cables Additional Equipment Required EquipmentTools Table 2-1 Cable Distance Limitations Front Rack Mounting InstallationTerminal or PC Figure 2-2 Front Rack Mounting the Chassis Tabletop Mounting Interface Connections and First Time Start-Up Making ConnectionsManagement Serial Port Connections Connecting a Terminal or PC to the System Front Serial Craft Port Figure 3-2 Connecting to the System Remotely Connecting RemotelyPower Connections Figure 3-3 System Rear View Power Connections Operation Startup andNormal LED Displays Error message POST Error Beep CodesBIOS Generated POST Error Beep Codes BMC Generated POST Beep Codes 3COM Security Switch 6200 Hardware and Software Users Guide Beep POST Memory Error 3-Beep Codeserror Codes Debug port 80h First Time Startup 3. Define the Time Zone 6. Configure the SNMP parameters 3-105. Define the Management Services 4. Select a region The following is an example display showing configured users 3-117. Configure the individual user accounts 8. Configure the host interfaces 3-12 9. Configure all additional interfaces10. Configure your default gateway 3-13 11. Configure NTP to achieve time synchronization 3-14 Configuring the Security Switch System Configuring Parameterschoices. The Enter key is used to select default values 2. To change any of the system parameters enter y, or press the Return key to leave system parameters unchanged 3COM Security Switch 6200 Hardware and Software Users Guide Configuring User Accounts Time Protocol Resolutionthe Network Domain Name 2. Configure SNMP Servers. For example Configuring the Simple Network Management Protocol SNMPTo configure SNMP 1. Select Option 5 from the main menu 3. Enter the desired option or enter X to return to the main menu 4. Configure SNMP Communities. For example 6. Configure SNMP Trap Destinations. For example Interfaces 4-10 4-11 4-12 1. Select Option 7 from the main menu Configuring Network Interfaces 4-13 IP Aliases 4-14interface. To configure IP Aliases 4-15 Configuring Static Routes 4-16 Configuring Static ARP Entries 4-17 Configuring the Virtual Router Redundancy Protocol VRRP 4-18 4-19 4-20 Exiting from the Configuration Tool Saving Your System ConfigurationConfiguration Restoring 4-22 address=10.1.1.50 data /dnsserver 4-23 ipinterface data ifname=management 1 address=192.168.10.6 /data 4-24 ipaddr=128.205.1.31 macaddr=0000a2000003 /data statichost account system to DefaultSettings Factory 4-26 Upgrading the System Software Upgrading the System Software Answer Y when this command prompts you Software Safe Upgrade Upgrading the System Software Using the Safe Upgrade andRollback Features Upgrading from Version 6. Savew the partition table by entering the letter “w” Upgrading from Version 2.1 and Greater Upgrading from Software to a UP While an RP is Operational Rollback Online ServicesTechnical Support Technical Your Network 3Com Knowledgebase Web ServicesSupport from Supplier Telephone Support Support from 3ComEmail Support Asia, Pacific Rim Telephone Number Telephone Support NumbersCountry Asia, Pacific Rim Latin America North America Fax Numbers for return authorization numbers Returning Products for Repair Country 3COM Security Switch 6200 Hardware and Software Users GuideTechnical Support Telephone Number 3COM Security Switch 6200 Hardware and Software Users Guide Environmental Characteristics Technical SpecificationsPhysical Characteristics Power Characteristics Technical Specifications Signal Connector Pin AssignmentsDB-9 Connector Pin Number Connector Pin Assignments Regulatory Standards Compliance SafetyRegulatory Information CE marking for the EEA European Economic Area Radio Frequency Interference EMI ComplianceImmunity Compliance VCCI Statement V-3/2000.04