Technical Specifications, Physical Characteristics | 3Com 6200


		A
	Technical Specifications	A
	Technical Specifications

This appendix lists the physical, environmental, and power characteristics of the 3COM Security Switch 6200.

Physical Characteristics

Size (Inches): 3.5 H x 17.5 W x 25.5 D

Weight: approximately 32 lbs

Environmental Characteristics

Operating Temperature: 0 to +40 degrees C

Storage Temperature: -20 to +65 degrees C

Relative Humidity: 10 to 95 percent, non-conducting

Operating Altitude: 0 to 10,000 feet above sea level

Power Characteristics

Power: 100 to 240 VAC, 350W

3COM Security Switch 6200 Hardware and Software Users Guide

A-1

Image 73

3Com 6200 manual Technical Specifications, Physical Characteristics, Environmental Characteristics, Power Characteristics

Contents

10/100 Security Switch Hardware and Software Users Guides10/100/1000 FIBER ENVIRONMENTAL STATEMENT UNITED STATES GOVERNMENT LEGENDEnd of Life Statement Regulated Materials Statement Installation Contents3COM Security Switch 6200 Hardware and Software Users Guide About this Guide Technical Specifications 4 Configuring the Security Switch 6200 System5 Upgrading the System Software Technical Support Regulatory Information Connector Pin AssignmentsSafety Regulatory Standards Compliance 3COM Security Switch 6200 Hardware and Software Users Guide Intended About this GuideAudience Conventions Security Switch 6200 Product Release Notes 3COM Security Switch 6200 Hardware and Software Users GuideInstall Server Installation and Configuration Guide Security Switch 6200 Applications Guide System IntroductionComponents Figure 1-1 6200 Front View ChassisFigure 1-2 Rear Panel Component Layout Management Options Configuration ToolFirst Time Startup Interview Introduction Before You Start Installation Requirement Site RequirementsDescription MGMT1 MGMT2 SYS HDD Figure 2-1 3COM Security Switch 6200 Shipping Contents10/100 FIBER Tools Additional Equipment Required EquipmentCables Table 2-1 Cable Distance Limitations Terminal or PC InstallationFront Rack Mounting Figure 2-2 Front Rack Mounting the Chassis Tabletop Mounting Making Connections Interface Connections and First Time Start-UpManagement Serial Port Connections Connecting a Terminal or PC to the System Front Serial Craft Port Power Connections Connecting RemotelyFigure 3-2 Connecting to the System Remotely Figure 3-3 System Rear View Power Connections Normal Startup andOperation LED Displays BIOS Generated POST Error Beep Codes POST Error Beep CodesError message BMC Generated POST Beep Codes Interface Connections and First Time Start-Up error Codes POST Memory Error 3-Beep CodesBeep Debug port 80h First Time Startup 3. Define the Time Zone 5. Define the Management Services 3-106. Configure the SNMP parameters 4. Select a region 7. Configure the individual user accounts 3-11The following is an example display showing configured users 8. Configure the host interfaces 9. Configure all additional interfaces 3-1210. Configure your default gateway 11. Configure NTP to achieve time synchronization 3-13 3-14 Configuring the Security Switch System Parameters Configuringchoices. The Enter key is used to select default values 2. To change any of the system parameters enter y, or press the Return key to leave system parameters unchanged 5. Define the Management Services Configuring User Accounts the Network ResolutionTime Protocol Domain Name To configure SNMP 1. Select Option 5 from the main menu Configuring the Simple Network Management Protocol SNMP2. Configure SNMP Servers. For example 3. Enter the desired option or enter X to return to the main menu 4. Configure SNMP Communities. For example 6. Configure SNMP Trap Destinations. For example 4-10 Interfaces 4-11 1. Select Option 7 from the main menu 4-12 4-13 Configuring Network Interfaces 4-14 IP Aliasesinterface. To configure IP Aliases 4-15 4-16 Configuring Static Routes 4-17 Configuring Static ARP Entries 4-18 Configuring the Virtual Router Redundancy Protocol VRRP 4-19 4-20 Configuration Saving Your System ConfigurationExiting from the Configuration Tool Restoring address=10.1.1.50 data /dnsserver 4-22 ipinterface data ifname=management 1 address=192.168.10.6 /data 4-23 ipaddr=128.205.1.31 macaddr=0000a2000003 /data statichost account 4-24 Settings Defaultsystem to Factory 4-26 Upgrading the System Software Upgrading the System Software Answer Y when this command prompts you Rollback Features Upgrading the System Software Using the Safe Upgrade andSoftware Safe Upgrade Upgrading from Version 6. Savew the partition table by entering the letter “w” Upgrading from Version 2.1 and Greater Upgrading from Software to a UP While an RP is Operational Rollback Technical Support ServicesOnline Technical Support from 3Com Knowledgebase Web ServicesYour Network Supplier Email Support Support from 3ComTelephone Support Asia, Pacific Rim Country Telephone Support NumbersTelephone Number Asia, Pacific Rim North America Latin America Returning Products for Repair Fax Numbers for return authorization numbers Technical Support 3COM Security Switch 6200 Hardware and Software Users GuideCountry Telephone Number Technical Support Physical Characteristics Technical SpecificationsEnvironmental Characteristics Power Characteristics Technical Specifications DB-9 Connector Connector Pin AssignmentsSignal Pin Number Connector Pin Assignments Regulatory Information SafetyRegulatory Standards Compliance CE marking for the EEA European Economic Area Immunity Compliance EMI ComplianceRadio Frequency Interference VCCI Statement V-3/2000.04