Modifying Marker Data to be Written | 3M 2250M-iD, 2273M-iD specs

Step 8. After writing to the 3M™ iD Marker is completed, the following screen will be displayed. The following messages may appear in the writing process.

−− Message 1. If the overwrite option was set to "No" And there was data present on the target market then the following screen will be displayed;

−− Message 2. When writing to a passive marker or the wrong frequency then the following will be displayed.

−− Message 3. This screen indicates that X-Type marker option was incorrectly set to "Yes" or "No". Verify the serial number that is displayed on the marker ends with an “X” to select "Yes" for X-Type, else select "No".

Note: Once the marker data has been locked, the information contained on the marker is PERMANENT. Choosing to permanently lock the marker data is irreversible. Once the data is locked it can not be overwritten. Assure that the data that is being written is correct before proceeding.

A. Modifying Marker Data to be Written

To alter the information to be written into the marker

Press Menu [6] + Write Mode [SK:1]

Step 1. Select a template from the list on the display to be written into the marker by pressing the up/down arrows [SK] to highlight the preferred template. ‘Last Written/Read’ is the most recent data that was written to/read from a marker by the receiver.

48	78-8130-6150-0 Rev G

Image 48

3M 2250M-iD, 2273M-iD manual Modifying Marker Data to be Written, Press Menu 6 + Write Mode SK1

Contents

3M Dynatel Contents Rev G Rev G Rev G Safety Information Intended Use About This Manual Transmitter Battery Installation Quick Start Receiver Battery Installation Cleaning Service and Accessories 3M Dynatel Transmitter 2273 Keypad and Connector Definitions Rechargeable Battery Maximum Transmitter Output 3M Dynatel Receiver 2250M Key Pad and Display Definitions Dynatel 3M Dynatel Receiver 2273M Key Pad and Display Definitions Menu Displays Main Menu Rev G Rev G Configuring The Receiver Setting the Receiver ClockSelect Depth Units Selecting a Language Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6j Enabling/Disabling FrequenciesCreating User Defined Frequencies Filtering Power Frequency Interference Selecting Locating Audio Buried Cables And Pipes Transmitter Connections Direct Connect Method Rev G Dyna-Coupler Method Non-Sweeping Passive Induction Mode Locating Induction Method Sweeping Active Induction Mode Locating Passive Sweeps One-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-up Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK Toggle Locate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK ToggleReceiver Modes Directional Peak Dir Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Special Peak Spl Pk Expanded Mode Locate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK ToggleDepth and Current Estimate Induction Peak Ind Pk Locating Frequencies Active Frequencies Power Frequencies Passive FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Locating Active Duct Probes Sondes Determining ADP Depth Locating Buried Sheath Faults and Earth Return Faults Transmitter Setup Pinpointing the Buried Fault Green Band Alert Mode Locating 3M Electronic Markers 3M iD MarkersEnabling/Disabling Marker Types Single Marker Locate Press Locate/OK Dual Marker Locate 3M iD Marker Depth Passive 3M Electronic Marker Non-iD Depth Creating/Editing Templates for 3M iD Markers Creating New TemplatesMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Menu 6 + Write Mode SK1 Writing 3M iD Markers Press Start Write SK Press Menu 6 + Write Mode SK1 Modifying Marker Data to be Written Rev G Reading 3M iD Markers Reviewing Marker Read/Write History Read HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Capturing the GPS Coordinates Capture Mode / Mode GPS OperationWrite History SK Communicating with the GPS Device Menu 6 + COM Setup SK3 + GIS Path Mapping with GPS Creating Trace Templates Menu 6 + Com SK3 + GIS SK or PDA SK Aerial Faults Toning Additional Applications Connection Diagrams Cable Identification Help Mode Menu 6 + More SK4 + Help SK8 Self Test Of Receiver Menu 6 + More SK4 + Self Test SK7 Product Description And Optional Accessories Standard ConfigurationsProduct Description Direct Connect Cables Earth Contact Frame Optional 3M Accessories for 3M Dynatel Locators Receiver Specifications Specification Detection Depth 3M Non-iD Passive Transmitter Specifications Mode can display a fault resistance up to 10M Ω Environmental and Regulatory Specifications Rechargeable Battery Information Rev G Electrical Markets Division Important Notice