Configuring The Receiver, Select Depth Units | 3M 2273M-iD, 2250M

5. Configuring The Receiver

In the setup mode, the units of depth measurement, time, date, and date format can be set. The receiver can be configured to detect only certain frequencies and/or specific utility markers (3M™ Dynatel™ Receivers 2250M-iD and 2273M-iD only). User defined frequencies can be programmed, language of the receiver can be selected, and tone frequencies set.

A. Select Depth Units

MENU [6] + >>More [SK:4] + Setup [SK:6] + Units [SKToggle:6a]

1.Press Units [SK toggle:6a].

2.The soft key command will toggle between inches (in), centimeters (cm), and feet/inches (ft-in).

3.Press Locate/OK [5].

B. Setting the Receiver Clock

Set the time, date, and date format of the receiver. Depth and Current measurements are time and date stamped, as well as read write marker information (iD units only).

MENU [6] + >>More [SK:4] + Setup [SK:6] + Clock [SK:6b]

1.Press the left/right arrow [SK] to highlight the digit of the date or time to change.

2.Press the + or - [SK] to increment or decrement.

3.When the date format is highlighted, the format will toggle between mm/dd/yy and dd/mm/yy.

4.Press Locate/OK [5] to save, or Menu [6] to cancel.

C. Selecting a Language

MENU [6] + >>More [SK:4] + Setup [SK:6] + Lang [SKToggle:6c]

The soft key command will cycle through available languages. Press Locate/OK [5]. Alternate languages can be uploaded to the receiver using the 3M™ Dynatel™ PCTools Software. The 3M™ Dynatel™ PC Tool Kit Software is available free of charge at www.3M.com/dynatel under the Software section; 2550/2573/2250M/2273M/1420 Locator PC Tools xx.x.x (EXE xx.xMB).

18	78-8130-6150-0 Rev G

Image 18

3M 2273M-iD, 2250M-iD Configuring The Receiver, Select Depth Units, Setting the Receiver Clock, Selecting a Language

Contents

3M Dynatel Contents Rev G Rev G Rev G Safety Information Intended Use About This Manual Transmitter Battery Installation Quick Start Receiver Battery Installation Cleaning Service and Accessories 3M Dynatel Transmitter 2273 Keypad and Connector Definitions Rechargeable Battery Maximum Transmitter Output 3M Dynatel Receiver 2250M Key Pad and Display Definitions Dynatel 3M Dynatel Receiver 2273M Key Pad and Display Definitions Menu Displays Main Menu Rev G Rev G Select Depth Units Configuring The ReceiverSetting the Receiver Clock Selecting a Language Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6j Enabling/Disabling FrequenciesCreating User Defined Frequencies Filtering Power Frequency Interference Selecting Locating Audio Buried Cables And Pipes Transmitter Connections Direct Connect Method Rev G Dyna-Coupler Method Non-Sweeping Passive Induction Mode Locating Induction Method Sweeping Active Induction Mode Locating Passive Sweeps One-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-up Receiver Modes Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Directional Peak Dir Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Special Peak Spl Pk Depth and Current Estimate Expanded ModeLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Induction Peak Ind Pk Locating Frequencies Active Frequencies Power Frequencies Passive FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Locating Active Duct Probes Sondes Determining ADP Depth Locating Buried Sheath Faults and Earth Return Faults Transmitter Setup Pinpointing the Buried Fault Green Band Alert Mode Locating 3M Electronic Markers 3M iD MarkersEnabling/Disabling Marker Types Single Marker Locate Press Locate/OK Dual Marker Locate 3M iD Marker Depth Passive 3M Electronic Marker Non-iD Depth Creating/Editing Templates for 3M iD Markers Creating New TemplatesMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Menu 6 + Write Mode SK1 Writing 3M iD Markers Press Start Write SK Press Menu 6 + Write Mode SK1 Modifying Marker Data to be Written Rev G Reading 3M iD Markers Reviewing Marker Read/Write History Read HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Write History SK Capturing the GPS Coordinates Capture Mode / ModeGPS Operation Communicating with the GPS Device Menu 6 + COM Setup SK3 + GIS Path Mapping with GPS Creating Trace Templates Menu 6 + Com SK3 + GIS SK or PDA SK Aerial Faults Toning Additional Applications Connection Diagrams Cable Identification Help Mode Menu 6 + More SK4 + Help SK8 Self Test Of Receiver Menu 6 + More SK4 + Self Test SK7 Product Description Product Description And Optional AccessoriesStandard Configurations Direct Connect Cables Earth Contact Frame Optional 3M Accessories for 3M Dynatel Locators Receiver Specifications Specification Detection Depth 3M Non-iD Passive Transmitter Specifications Mode can display a fault resistance up to 10M Ω Environmental and Regulatory Specifications Rechargeable Battery Information Rev G Electrical Markets Division Important Notice