Dual Marker Locate, 3M iD Marker Depth | 3M 2250M-iD, 2273M-iD

D. Dual Marker Locate

1.Press Locate/OK [5].

2.Press Marker [SK].

3.Press MARKR 1 [SK Toggle] to select desired utility.

4.Press MARKR 2 [SK Toggle] to select desired utility.

Note: Only the marker types enabled in the setup menu will be shown. (See Enabling/ Disabling Marker types, Section 13A). When scanning for markers, the gain level [4] should be set high.

−− The third and fourth soft key commands will populate with the types of utilities selected for Marker 1 and Marker 2.

5.Adjust the Gain [4] down until the bar graphs open.

−− The bar graph will close, the audio will increase, and the Signal Strength [10] will increase when the receiver detects a marker of the specified utility.

−− When one of the two markers is detected, press the “XXX Only” [SK] for the detected utility marker. ("XXX" represents the marker types selected. In the above example, PWR Only and TEL Only.)

−− The receiver will switch to Single Marker Locate in order to pinpoint the marker.

6.Press Markr 2 [SK Toggle] to return to Dual Marker Locate.

E. 3M™ iD Marker Depth

1.Lower the tip of the receiver to the ground over the pinpointed marker.

2.Press Depth [SK].

−− The receiver will examine the marker (Calculating, please wait...)

−− If the marker is a 3M™ iD Marker, the receiver will display the depth of the marker, and its identification serial number.

78-8130-6150-0 Rev G

41

Image 41

3M 2250M-iD, 2273M-iD manual Dual Marker Locate, 3M iD Marker Depth

Contents

3M Dynatel Contents Rev G Rev G Rev G Intended Use Safety Information About This Manual Quick Start Transmitter Battery Installation Receiver Battery Installation Service and Accessories Cleaning 3M Dynatel Transmitter 2273 Keypad and Connector Definitions Maximum Transmitter Output Rechargeable Battery Dynatel 3M Dynatel Receiver 2250M Key Pad and Display Definitions 3M Dynatel Receiver 2273M Key Pad and Display Definitions Main Menu Menu Displays Rev G Rev G Setting the Receiver Clock Configuring The ReceiverSelect Depth Units Selecting a Language Creating User Defined Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jEnabling/Disabling Frequencies Selecting Locating Audio Filtering Power Frequency Interference Direct Connect Method Buried Cables And Pipes Transmitter Connections Rev G Dyna-Coupler Method Induction Method Non-Sweeping Passive Induction Mode Locating Passive Sweeps Sweeping Active Induction Mode Locating One-person Active Induction Mode Sweeps Transmitter Set-up Two-person Active Induction Mode Sweeps Locate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleReceiver Modes Directional Peak Dir Pk Special Peak Spl Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Locate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Expanded ModeDepth and Current Estimate Induction Peak Ind Pk Active Frequencies Locating Frequencies Auxiliary Frequencies Power FrequenciesPassive Frequencies Locating in Directional Peak Mode Rev G Determining ADP Depth Locating Active Duct Probes Sondes Transmitter Setup Locating Buried Sheath Faults and Earth Return Faults Pinpointing the Buried Fault Green Band Enabling/Disabling Marker Types Alert ModeLocating 3M Electronic Markers 3M iD Markers Press Locate/OK Single Marker Locate 3M iD Marker Depth Dual Marker Locate Passive 3M Electronic Marker Non-iD Depth Menu 6 + Data/Templat SK2 + User Templat SK2c Creating/Editing Templates for 3M iD MarkersCreating New Templates Rev G Editing Templates Writing 3M iD Markers Menu 6 + Write Mode SK1 Press Start Write SK Modifying Marker Data to be Written Press Menu 6 + Write Mode SK1 Rev G Reading 3M iD Markers Menu 6 + Data/Templat SK2 + Read History SK2a Reviewing Marker Read/Write HistoryRead History GPS Operation Capturing the GPS Coordinates Capture Mode / ModeWrite History SK Communicating with the GPS Device Path Mapping with GPS Menu 6 + COM Setup SK3 + GIS Menu 6 + Com SK3 + GIS SK or PDA SK Creating Trace Templates Additional Applications Aerial Faults Toning Cable Identification Connection Diagrams Menu 6 + More SK4 + Help SK8 Help Mode Menu 6 + More SK4 + Self Test SK7 Self Test Of Receiver Standard Configurations Product Description And Optional AccessoriesProduct Description Direct Connect Cables Earth Contact Frame Optional 3M Accessories for 3M Dynatel Locators Specification Receiver Specifications Detection Depth 3M Non-iD Passive Mode can display a fault resistance up to 10M Ω Transmitter Specifications Rechargeable Battery Information Environmental and Regulatory Specifications Rev G Important Notice Electrical Markets Division