About This Manual | 3M 2250M-iD, 2273M-iD specification

!WARNING

This WARNING applies to the use of the Direct Connect Cables and the Transmitter.

To avoid potential shock, or electrically damaging the Transmitter, when setting up the Transmitter to locate using the Direct Connect method, follow these basic steps;

•ALWAYS plug the Direct Connect Cable into the Transmitter Output Jack [T-6] BEFORE connecting the leads to the cable/pipe to be located and the ground rod.

–Connect the red lead to the cable/pipe.

–Connect the black lead to ground rod.

A POTENTIAL FOR ELECTRICAL SHOCK, AND/OR TRANSMITTER ELECTRICAL DAMAGE, EXISTS WHEN USING THE DIRECT CONNECT CABLE ON CABLES ENERGIZED WITH ELECTRICAL POWER IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED. USE APPROPRIATE SAFETY PROCEDURES.

CHECK VOLTAGE BEFORE CONNECTING TRANSMITTER. VOLTAGE HIGHER THAN 240 VOLTS WILL DAMAGE EQUIPMENT. FOLLOW STANDARD PROCEDURES FOR REDUCING THE VOLTAGE.

2. About This Manual

There are two basic models included in the 3M™ Dynatel™ Locator 2200M Series. The 2250M locator is designed for cable/pipe locating. The 2273M locator is designed for cable/pipe and fault locating. The iD option (read/write capability to 3MTM iD Markers) is available for both models. There are three transmitter options: 3 Watt, 5 Watt, or 12 Watt. This instruction manual will include all features. All instructions are applicable to all products, unless noted.

The 12-watt transmitter option offers additional power output levels for improved induction performance and 8 kHz (low frequency) induction for shallow facilities, such as risers. Output Power up to 12 Watts for the 12-watt transmitter is achieved using the supplied external power source. The maximum output power in Direct Connect method is reduced to below FCC limits. (FCC limits: 1 Watt at 200 kHz and 10 Watts at 33 kHz)

In order to demonstrate all available functions, the illustrations depict the 2273M-iD receiver unit and the 2250 and 2273 12-watt transmitters. The 2250M receiver may vary from the illustrations shown.

78-8130-6150-0 Rev G

7

Image 7

3M 2250M-iD, 2273M-iD manual About This Manual

Contents

3M Dynatel Contents Rev G Rev G Rev G Intended Use Safety Information About This Manual Quick Start Transmitter Battery Installation Receiver Battery Installation Service and Accessories Cleaning 3M Dynatel Transmitter 2273 Keypad and Connector Definitions Maximum Transmitter Output Rechargeable Battery Dynatel 3M Dynatel Receiver 2250M Key Pad and Display Definitions 3M Dynatel Receiver 2273M Key Pad and Display Definitions Main Menu Menu Displays Rev G Rev G Selecting a Language Configuring The ReceiverSetting the Receiver Clock Select Depth Units Enabling/Disabling Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jCreating User Defined Frequencies Selecting Locating Audio Filtering Power Frequency Interference Direct Connect Method Buried Cables And Pipes Transmitter Connections Rev G Dyna-Coupler Method Induction Method Non-Sweeping Passive Induction Mode Locating Passive Sweeps Sweeping Active Induction Mode Locating One-person Active Induction Mode Sweeps Transmitter Set-up Two-person Active Induction Mode Sweeps Directional Peak Dir Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Receiver Modes Special Peak Spl Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Induction Peak Ind Pk Expanded ModeLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Depth and Current Estimate Active Frequencies Locating Frequencies Passive Frequencies Power FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Determining ADP Depth Locating Active Duct Probes Sondes Transmitter Setup Locating Buried Sheath Faults and Earth Return Faults Pinpointing the Buried Fault Green Band Locating 3M Electronic Markers 3M iD Markers Alert ModeEnabling/Disabling Marker Types Press Locate/OK Single Marker Locate 3M iD Marker Depth Dual Marker Locate Passive 3M Electronic Marker Non-iD Depth Creating New Templates Creating/Editing Templates for 3M iD MarkersMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Writing 3M iD Markers Menu 6 + Write Mode SK1 Press Start Write SK Modifying Marker Data to be Written Press Menu 6 + Write Mode SK1 Rev G Reading 3M iD Markers Read History Reviewing Marker Read/Write HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Communicating with the GPS Device Capturing the GPS Coordinates Capture Mode / ModeGPS Operation Write History SK Path Mapping with GPS Menu 6 + COM Setup SK3 + GIS Menu 6 + Com SK3 + GIS SK or PDA SK Creating Trace Templates Additional Applications Aerial Faults Toning Cable Identification Connection Diagrams Menu 6 + More SK4 + Help SK8 Help Mode Menu 6 + More SK4 + Self Test SK7 Self Test Of Receiver Direct Connect Cables Earth Contact Frame Product Description And Optional AccessoriesStandard Configurations Product Description Optional 3M Accessories for 3M Dynatel Locators Specification Receiver Specifications Detection Depth 3M Non-iD Passive Mode can display a fault resistance up to 10M Ω Transmitter Specifications Rechargeable Battery Information Environmental and Regulatory Specifications Rev G Important Notice Electrical Markets Division