Environmental and Regulatory Specifications | 3M 2250M-iD, 2273M

26. Environmental and Regulatory Specifications

Item	Specification
Standard	IP54
Regulatory	FCC compliant, FCC Part 15
Operating Temperature	-4°F to 122°F (-20°C to 50°C)
Storage Temperature	-4°F to 158° F (-20°C to 70°C)

27. Rechargeable Battery Information

UN2800 classification as “Batteries, wet, Non-Spillable, and electric storage” as a result of passing the Vibration and Pressure Differential Test described in DOT [49 CFR 173.159(d) and IATA/ICAO [Special Provision A67].

!CAUTION

To reduce the risks associated with environmental contamination and possible injury:

The 12W transmitter utilizes the 2200RB rechargeable battery for the Maximum Output Power level. This is a maintenance-free sealed lead (Pb)-acid battery.

•Replace the battery if the acid solution leaks.

•The batteries are not serviceable.

•Do not disassemble batteries.

•Do not remove vent caps.

•Do not rest tools or cables on batteries.

•Store lead-acid batteries with adequate ventilation.

•Do not heat batteries above 140°F (60°C)

•Never recharge batteries in an unventilated, enclosed space.

•Spent batteries must be treated as hazardous waste. Dispose of batteries and electronic components in accordance with all regulations.

•Do not incinerate batteries.

•Always remove/disconnect batteries when not in use or storing for long periods of time.

64	78-8130-6150-0 Rev G

Image 64

3M 2250M-iD, 2273M-iD manual Environmental and Regulatory Specifications, Rechargeable Battery Information

Contents

3M Dynatel Contents Rev G Rev G Rev G Safety Information Intended Use About This Manual Transmitter Battery Installation Quick Start Receiver Battery Installation Cleaning Service and Accessories 3M Dynatel Transmitter 2273 Keypad and Connector Definitions Rechargeable Battery Maximum Transmitter Output 3M Dynatel Receiver 2250M Key Pad and Display Definitions Dynatel 3M Dynatel Receiver 2273M Key Pad and Display Definitions Menu Displays Main Menu Rev G Rev G Configuring The Receiver Setting the Receiver ClockSelect Depth Units Selecting a Language Enabling/Disabling Frequencies Menu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6jCreating User Defined Frequencies Filtering Power Frequency Interference Selecting Locating Audio Buried Cables And Pipes Transmitter Connections Direct Connect Method Rev G Dyna-Coupler Method Non-Sweeping Passive Induction Mode Locating Induction Method Sweeping Active Induction Mode Locating Passive Sweeps One-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-up Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK Toggle Locate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK ToggleReceiver Modes Directional Peak Dir Pk Locate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Special Peak Spl Pk Expanded Mode Locate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK ToggleDepth and Current Estimate Induction Peak Ind Pk Locating Frequencies Active Frequencies Passive Frequencies Power FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Locating Active Duct Probes Sondes Determining ADP Depth Locating Buried Sheath Faults and Earth Return Faults Transmitter Setup Pinpointing the Buried Fault Green Band Locating 3M Electronic Markers 3M iD Markers Alert ModeEnabling/Disabling Marker Types Single Marker Locate Press Locate/OK Dual Marker Locate 3M iD Marker Depth Passive 3M Electronic Marker Non-iD Depth Creating New Templates Creating/Editing Templates for 3M iD MarkersMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Menu 6 + Write Mode SK1 Writing 3M iD Markers Press Start Write SK Press Menu 6 + Write Mode SK1 Modifying Marker Data to be Written Rev G Reading 3M iD Markers Read History Reviewing Marker Read/Write HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Capturing the GPS Coordinates Capture Mode / Mode GPS OperationWrite History SK Communicating with the GPS Device Menu 6 + COM Setup SK3 + GIS Path Mapping with GPS Creating Trace Templates Menu 6 + Com SK3 + GIS SK or PDA SK Aerial Faults Toning Additional Applications Connection Diagrams Cable Identification Help Mode Menu 6 + More SK4 + Help SK8 Self Test Of Receiver Menu 6 + More SK4 + Self Test SK7 Product Description And Optional Accessories Standard ConfigurationsProduct Description Direct Connect Cables Earth Contact Frame Optional 3M Accessories for 3M Dynatel Locators Receiver Specifications Specification Detection Depth 3M Non-iD Passive Transmitter Specifications Mode can display a fault resistance up to 10M Ω Environmental and Regulatory Specifications Rechargeable Battery Information Rev G Electrical Markets Division Important Notice