Manuals / 3M / Kitchen Appliance / Food Saver

3M 40800 Specifications, 4.1Power Requirements, 4.2Operating Rate, 4.3Operating Conditions

Models: 40800

1 144

Download 144 pages 27.28 Kb

Page 24

4-SPECIFICATIONS

4-SPECIFICATIONS

4.1Power Requirements

Electrical: 120 Volt, 60Hz

Pneumatic: 5 bar gauge pressure [70PSIG]

110 liter/min @ 21°C, 1.01 bar [3.75 SCFM] at 15 boxes per minute A pressure regulator is included

4.2Operating Rate

Box drive belt speed is approximately 0.5 m/s [100 feet per minute].

4.3Operating Conditions

Use in dry, relatively clean environments at 5o C to 50o C [40o F to 120o F] with clean, dry boxes. Note: Machine should not be washed or subjected to conditions causing moisture condensation on

components.

WARNING

• To reduce the risk associated with fire and explosion hazards:

− Do not operate this equipment in poten-

tially ﬂammable or explosive environments.

4.4Tape

Scotch® pressure-sensitive ﬁlm box sealing tapes.

4.5Tape Width

36mm [1 1/2 inch] minimum to 48mm [2 inch] maximum

700r-NA

14

2011 July

Image 24

3M 40800 Specifications, 4.1Power Requirements, 4.2Operating Rate, 4.3Operating Conditions, 4.4Tape, 4.5Tape Width

Contents

Important Safety Information Random Case Sealerwith AccuGlide Taping Heads 700r Type3M Industrial Adhesives and Tapes 3M Center, Building 220-5E-06 St. Paul, MNReplacement Parts and Service Information THIS PAGE IS BLANK Safety Technical Specifications700r Random Case Sealer PageTHIS PAGE IS BLANK TABLE OF CONTENTS continued Installation10. Safety devices 5. Shipment, Handling, and StorageTHIS PAGE IS BLANK TABLE OF CONTENTS continued 11. Setup and Adjustments13. Maintenance 12. OperationABBREVIATIONS AND ACRONYMS LIST OF ABBREVIATIONS, ACRONYMS1-INTRODUCTION 3M-MaticTM 700r Random Case Sealer, Type1.2.2 Manual Maintenance 1-INTRODUCTION continued1.2.1 Importance of the Manual 1.2.3 Consulting the Manual2-GENERALINFORMATION 2.1 Data Identifying Manufacturer and Machine700r-NA 2011 July2-GENERALINFORMATION continued 2.2 Warranty Contents—700rRandom Case Sealer3-SAFETY 3.1 General Safety InformationFigure 3.3 Table of Warnings Figure •To reduce the risk associated with muscle strain•To reduce the risk associated with pinch hazards Figure Figure Figure3.4 Operators Qualifications Skill 1: Machine Operator 3-SAFETY continued Upper Taping Head Emergency Stop Switch MachineBedUpper Head Assembly Adjustable Side Guides PowerImportant Safeguards continued 78-8070-1421-82 Figure 3-10– Replacement Labels/3M Part Numbers78-8095-1141-9 STOP78-8070-1319-4 78-8068-3859-1Important Safeguards continued 78-8070-1336-82 Figure 3-11– Replacement Labels/3M Part Numbers78-8070-1332-7 78-8098-8908-8 78-8070-1328-5 78-8070-1333-5 78-8070-1317-8Important Safeguards continued 78-8113-6768-5 4-SPECIFICATIONS 4.1Power Requirements4.2Operating Rate 4.3Operating Conditions4-SPECIFICATIONS continued Specifications 4-SPECIFICATIONS continued Control Side 5-SHIPMENT-HANDLING-STORAGE,TRANSPORT 6-UNPACKING 6.1 UncratingRemoval of Pallet Figure7-INSTALLATION 7-INSTALLATION continued 7.6 Assembly Completion / Machine Setup7.5 Removal of Plastic Ties Figure Figure7-INSTALLATION continued Machine Setup continuedSee Figure 7-7B 7-INSTALLATIONAND SETUP continued Column Guards C Figure 7-7– 700r Frame Setup7-INSTALLATIONAND SETUP continued 7-INSTALLATIONAND SETUP continued 7.12 Box Size Capacity of Case Sealer7.13 Electrical Connections and Controls • To reduce the risk associated7-INSTALLATIONAND SETUP continued 7-INSTALLATIONAND Setup continued 7-INSTALLATIONAND Setup continued 7-INSTALLATIONAND Setup continued 9.Mechanical Latch, Upper Drive Assembly – Figure10.Indicator, Air Pressure 8. Main Air Pressure Gauge7-INSTALLATIONAND Setup continued 7-INSTALLATIONAND SETUP continued 7.16Tape Loading and Threading7.17 Theory of Operation 7.18 Box Sealing7-INSTALLATION continued 7.23 Inspection of PhasesFor Three-MainPhases Only 7.19Completion of Taping HeadsFigure 8.3.1 Normal Stop Procedure 8-THEORYOF OPERATION8.1 Description of the Working Cycle 8.2 Definition of Running Mode9-CONTROLS 9.4 Upper Drive Raising Switch Pneumatic Valve Drive Assembly Raising SwitchFigure Figure Upper Drive Actuator Switch 9.6 Upper Drive Assembly Actuator Switch Figure9-CONTROLS continued 10-SAFETYDEVICES OF THE MACHINE 11 - SET UP AND ADJUSTMENTS 11 - SET UP AND ADJUSTMENTS continued 11.5Run Boxes to Inspect Adjustment FigureSection 13 / Maintenance and Repairs •To reduce the risk associated with pinch hazards12-OPERATION Troubleshooting 12.9 Troubleshooting GuideProblem CauseTroubleshooting continued Troubleshooting GuideProblem Cause13-MAINTENANCEAND REPAIRS Maintenance continued 13.8Box Drive Belt ReplacementFigure 13-4– Lower Drive Belt Replacement Figure 13-5– Upper Drive Belt Replacement13-MAINTENANCEAND REPAIRS continued Adjustments continued Adjustments continued Installation Instructions - Column Bumper Special Setup Procedure continued Special Setup Procedure continued •To reduce the risk associated with muscle strainTHIS PAGE IS BLANK ________ THIS PAGE IS BLANK 14-ADDITIONALINSTRUCTIONS 16-TECHNICALDIAGRAMS 16.1 Electric Diagram 700r-NA2011 July 16-TECHNICALDIAGRAMS continued 16.2 Pneumatic Diagram700r-NA 2011 JulyTHIS PAGE IS BLANK 16.3 Spare Parts Order THIS PAGE IS BLANK Options and Accessories Option/Accessory700r Random Case Sealer, Type Frame Assemblies To Order PartsTHIS PAGE IS BLANK 700r Random Case Sealer FigureFigure Figure700r Figure700r-NA 2011 July700r FigureRef. No 3M Part NoOPTIONAL 4051700r Ref. No3M Part No DescriptionCB A D C B A A EB FO GHI LMN3439-1 700r-NA 2011 July18a 18b 5670-1 700r 700r Random Case Sealer 71R/H 72L/H15238-1 71R/H 72L/H73R/H 74L/H15238-40 16 = 15104-1 68R/H 69L/H70R/H 71L/H15239-1 700r Random Case Sealer Figure 15239 /700r-NA 2011 July15239-38 9 8 9 7 12 10 13 146 59 13 15 16 2 700r 700r Random Case Sealer5919-1 700r Random Case Sealer Figure 700r-NA2011 July 700r-NA 2011 July700r Random Case Sealer Figure700r-NA 2011 July5921-1 THIS PAGE IS BLANK Instructions and Parts List 3M-Matic Accuglide Upper and Lower High SpeedTaping Heads 2 Inch TypePage Replacement Parts and Service Information THIS PAGE IS BLANK Replacement Parts And Service Information THIS PAGE IS BLANK Table of Contents Instruction Manual AccuGlide 3 High Speed 2 InchUpper and Lower Taping Heads Type PageWarranty Equipment Warranty and Limited Remedy Intended Use AccuGlide 3 Upper Taping Head - 2 inch, TypeTHIS PAGE IS BLANK Taping Head Contents How to use this ManualPart Name General InformationImportant Safeguards Important Safeguards continued Figure 1-1Replacement Labels/3M Part NumbersUpper Taping Head Label Lower Taping Head Label 78-8070-1335-0Specifications Specifications Installation Installation GuidelinesTape Width Adjustment Receiving And HandlingOperation Tape DrumTape Supply Roll Tape Adhesive Side•To reduce the risk associated with muscle strain Figure Figure 3-4– Tape Loading/ThreadingFigure 3-5– Tape Loading/Threading Maintenance Maintenance continued CleaningApplying/Buffing Roller Replacement Hex Socket Section View ofAdjustments Adjustments continued 0.5 - 0.9kg 1/2 lbs Adjusting NutApplying Mechanism Spring One-WayTension Roller FigureAdjustments continued The tape leg on the front of the Troubleshooting continued Troubleshooting Guide ProblemCause CorrectionSpare Parts/Service Information Replacement Parts Illustrations and Parts Lists AccuGlide 3 - Tape HeadAccuGlide 3 - 2 inch FigureAccuGlide 3 - Figure 10925 – Upper HeadAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10925 – 2 Upper HeadRef. No 3M Part NoAccuGlide 3 - Figure 10922 – Upper and Lower HeadsAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10922 – 2 Upper and Lower HeadsRef. No 3M Part NoAccuGlide 3 - Figure 10919 – Upper HeadAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10919 – 2 Upper HeadRef. No 3M Part NoAccuGlide 3 - Figure 10923 – Upper and Lower HeadsAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10923 – 2 Upper and Lower HeadsRef. No 3M Part NoAccuGlide 3 - Figure 10921 – Upper and Lower HeadsAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10921 – 2 Upper and Lower HeadsRef. No 3M Part NoAccuGlide 3 - Figure 10401 – Upper and Lower HeadsAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10401 – 2 Latch Upper and Lower HeadsRef. No 3M Part NoAccuGlide 3 - Figure 10924 – Lower HeadAccuGlide 3 - 2 - NA 2012 JanuaryAccuGlide 3 - Figure 10924 – 2 Lower HeadRef. No 3M Part No7 34 7 7 6 7 8 7AccuGlide 3 - Figure 10920 - Lower HeadAccuGlide 3 - Figure 10920– Lower HeadRef. No 3M Part NoTHIS PAGE IS BLANK