Manuals / 8e6 Technologies / Computer Equipment / Network Card

8e6 Technologies ERS-200 (5K02-52) quick start Check the Power Supply, Power Supply Precautions

Models: ERH-200 (5K02-24) ER3-200 (5K02-56) ERS-100 (5K02-51) ERS-200 (5K02-52) ERH-100 (5K02-61) ER3-100 (5K02-55)

1 74

Download 74 pages 30.79 Kb

Page 21

Check the Power Supply

This server is equipped with a universal power supply that handles 100-240 V, 50/60 Hz. A standard power cord interface (IEC 950) facilitates power plugs that are suitable for most European, North American, and Pacific Rim countries.

Power Supply Precautions

Warning:

•Use a regulating uninterruptible power supply (UPS) to protect the server from power surges, voltage spikes and to keep the server operating in case of a power failure.

•In geographic regions that are susceptible to electrical storms, 8e6 highly recom- mends plugging the AC power cord for the server into a surge suppressor.

•Use appropriately rated extension cords or power strips only.

•Allow power supply units to cool before touching them.

8e6 Enterprise Reporter Quick Start Guide

17

Image 21

8e6 Technologies ERS-200 (5K02-52), ER3-100 (5K02-55), ER3-200 (5K02-56) Check the Power Supply, Power Supply Precautions

Contents

GUIDE Release 5.0.00 / UpdatedQUICK START Model ERTrademarks 8e6 Enterprise Reporter Quick Start GuideService Information ContentsPreliminary Setup Procedures Install the Server“H” Server Specifications Regulatory Specifications and DisclaimersAppendix SCSI Connected Storage Device ER Enterprise Reporter Introduction Conventions Used in this Document About this DocumentProcedures Service Information8e6 Corporate Headquarters USA 8e6 TaiwanUnpack the Unit from the Carton Preliminary Setup ProceduresSelect a Site for the Server Front of bezel Install the “H” Server BezelOutside of left inner rail Inside front end of U-shapedE. Take up the free end of the bezel and also the loosened inner rail G. Slide the inner rail forward beneath the clips to lock it in place Rack Mount the Server Rack Setup PrecautionsRack Setup Suggestions Rack Mount Instructions for non-“H” ServersIdentify the Sections of the Rack Rails Install the Rack Rails Install the Chassis RailsInstalling the Server into a Telco Rack Install the Server into the RackYou should have received two rack rail assemblies with the 8e6 server unit. Each of these assemblies consists of two sections An inner fixed chassis rail that secures to the unit A, and an outer fixed rack rail that secures directly to the rack itself B. Two pairs of short brackets to be used on the front side of the outer rails are also included Identify the Sections of the Rack RailsInstall the Outer Rails Install the Inner RailsRack Mount Instructions for “H” Servers Rack Setup Suggestions8e6 Enterprise Reporter Quick Start Guide Install the Server into the RackIf you are installing the 8e6 server unit into a Telco type rack, follow the directions given on the previous page for rack installation. The only difference in the installation proce- dure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the Telco rack Installing the Server into a Telco RackPower Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Install the Server Step 1 Setup ProceduresQuick Start Setup Requirements Administrator Console Setup RequirementsStorage Device Setup for Attached Storage Units Step 1A Quick Start Setup ProceduresMonitor and Keyboard Setup Serial Console SetupHyperTerminal Setup Procedures Parity None Stop bits Flow control Hardware D. Specify the following session settings Bits per second Data bitsE. Click OK to connect to the HyperTerminal session 8e6 Enterprise Reporter Quick Start GuideG. Click the Settings tab, and at the Emulation menu select “VT100” Quick Start menu screen Login screenQuick Start menu administration menu Log Off, Disconnect the Peripherals System Status screenPreliminary Setup Step 1B Console Setup ProceduresWorkstation Configurations Storage Device Setup for Attached Storage UnitsA. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 port Link the Workstation to the ERThe Boot Up Process Network Setup Access the InternetLog in to the Administrator Console Network Settings C. Click OK to go to the main screen of the Administrator console8e6 Enterprise Reporter Quick Start Guide G. Enter the Second DNS IP address of the fallback DNS Regional Setting Time Zone Regional Setting NTP Servers Regional Setting LanguagePhysically Connect the ER to the Network Access the Internet Step 2 Change User Name and Password, Set Self- MonitoringC. Enter a User Name and Password Change User Name and PasswordC. Enter the Master Administrator’s E-Mail Address Set Self-MonitoringD. Select 8e6 Enterprise Reporter, and then click Save Step 3 R3000 ConfigurationStep 4 Client Workstation Configuration Step 5 Launch the ER Client F. Enter the Password, and Confirm Password Conclusion Important Information about using the ER in the Evaluation Mode Administrator Console, Expiration ScreenER Client, ER Server Statistics Window Non-“H” Server Specifications Physical SpecificationsSpecification ValueInternal Product Specifications Hardware Component SpecificationsER3-100 ER3-200Diagrams and Descriptions Front Panel LED Indicators and ButtonsLED Indicators and Buttons LED Indicator KeyERH-100 Value “H” Server SpecificationsERH-200 Value Physical SpecificationsERH-200 ERH-100Hardware Component Specifications Internal Product SpecificationsFront of Chassis Control Panel Rear of Chassis Safety Compliance Regulatory Specifications and DisclaimersDeclaration of the Manufacturer or Importer Electromagnetic Compatibility EMCIndustry Canada Equipment Standard for Digital Equipment ICES-003 Electromagnetic Compatibility Class A NoticeChina Compulsory Certification CCC - China 8e6 Enterprise Reporter Quick Start GuideEC Declaration of Conformity European Community Directives Requirement CEDeclaration of Conformity Other Required Installation Items Preliminary Setup ProceduresAppendix SCSI Connected Storage Device Unpack the Unit from the CartonRack Setup Precautions Rack Mount the ServerRack Mount Components Attach inner slide rail to chassis using 3 screws as shown StepAppendix SAN Installation StepAttach left and right rear long extended brackets to the outer rail using 2 screws, 2 washers, and 2 nuts for each bracket NOTE Make sure the flange is on the bottom edgeStep StepAttach outer rail to chassis using 4 screws and cage nuts per rail, 2 at each end StepStep Link the ER Unit with the SCSI Connected Device Install the UnitShut Down, Restart Procedures Shut Down the Storage Device UnitRestart the Storage Device Unit Physical Components Appendix SAN Installation8e6 Enterprise Reporter Quick Start Guide Temperature and Ventilation Status Power Supply StatusLED Display Disc Drive Alarm Management AlarmSilence Button Disk Drive ActivityTable 1 Physical Specifications SpecificationsTable 2 Hardware Component Specifications SATABoy Model Value8e6 Enterprise Reporter Quick Start Guide Appendix SAN Installation828 West Taft Avenue Orange, CA 92865-4232 Tel 714.282.6111 or 8e6 Corporate Headquarters USAFax 714.282.6116 Sales/Technical Support 714.282.6117 General Office Satellite Office