Manuals / 8e6 Technologies / Computer Equipment / Network Card

8e6 Technologies ERH-200 (5K02-24), ER3-100 (5K02-55), ER3-200 (5K02-56) quick start Rear of Chassis

Models: ERH-200 (5K02-24) ER3-200 (5K02-56) ERS-100 (5K02-51) ERS-200 (5K02-52) ERH-100 (5K02-61) ER3-100 (5K02-55)

1 74

Page 58

Rear of Chassis

UID (LED indicator) – On the rear of the chassis, to the left of the power supplies, a steady blue UID LED indicator displays when the UID button on the control panel is pressed. This LED remains lit until the UID button is pressed again.

Power Supplies (LED indicators) – The power supplies are located at the right on the rear of the chassis. An LED indicator is located above each of the power plugs.

54	8e6 Enterprise Reporter Quick Start Guide

Page 58

Image 58

8e6 Technologies ERH-200 (5K02-24), ER3-100 (5K02-55), ER3-200 (5K02-56), ERH-100 (5K02-61) quick start Rear of Chassis

Contents

QUICK START Release 5.0.00 / UpdatedGUIDE Model ER8e6 Enterprise Reporter Quick Start Guide TrademarksPreliminary Setup Procedures ContentsService Information Install the ServerRegulatory Specifications and Disclaimers “H” Server SpecificationsAppendix SCSI Connected Storage Device ER Enterprise Reporter Introduction About this Document Conventions Used in this Document8e6 Corporate Headquarters USA Service InformationProcedures 8e6 TaiwanPreliminary Setup Procedures Unpack the Unit from the CartonSelect a Site for the Server Outside of left inner rail Install the “H” Server BezelFront of bezel Inside front end of U-shapedE. Take up the free end of the bezel and also the loosened inner rail G. Slide the inner rail forward beneath the clips to lock it in place Rack Setup Precautions Rack Mount the ServerRack Mount Instructions for non-“H” Servers Rack Setup SuggestionsIdentify the Sections of the Rack Rails Install the Chassis Rails Install the Rack RailsInstall the Server into the Rack Installing the Server into a Telco RackIdentify the Sections of the Rack Rails You should have received two rack rail assemblies with the 8e6 server unit. Each of these assemblies consists of two sections An inner fixed chassis rail that secures to the unit A, and an outer fixed rack rail that secures directly to the rack itself B. Two pairs of short brackets to be used on the front side of the outer rails are also includedRack Mount Instructions for “H” Servers Install the Inner RailsInstall the Outer Rails Rack Setup SuggestionsInstall the Server into the Rack 8e6 Enterprise Reporter Quick Start GuideInstalling the Server into a Telco Rack If you are installing the 8e6 server unit into a Telco type rack, follow the directions given on the previous page for rack installation. The only difference in the installation proce- dure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the Telco rackCheck the Power Supply Power Supply PrecautionsGeneral Safety Information Server Operation and Maintenance PrecautionsAC Power Cord and Cable Precautions Electrical Safety PrecautionsMotherboard Battery Precautions Quick Start Setup Requirements Step 1 Setup ProceduresInstall the Server Administrator Console Setup RequirementsMonitor and Keyboard Setup Step 1A Quick Start Setup ProceduresStorage Device Setup for Attached Storage Units Serial Console SetupHyperTerminal Setup Procedures E. Click OK to connect to the HyperTerminal session D. Specify the following session settings Bits per second Data bitsParity None Stop bits Flow control Hardware 8e6 Enterprise Reporter Quick Start GuideG. Click the Settings tab, and at the Emulation menu select “VT100” Login screen Quick Start menu screenQuick Start menu administration menu System Status screen Log Off, Disconnect the PeripheralsWorkstation Configurations Step 1B Console Setup ProceduresPreliminary Setup Storage Device Setup for Attached Storage UnitsLink the Workstation to the ER A. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 portThe Boot Up Process Access the Internet Network SetupLog in to the Administrator Console C. Click OK to go to the main screen of the Administrator console Network Settings8e6 Enterprise Reporter Quick Start Guide G. Enter the Second DNS IP address of the fallback DNS Regional Setting Time Zone Regional Setting Language Regional Setting NTP ServersPhysically Connect the ER to the Network Step 2 Change User Name and Password, Set Self- Monitoring Access the InternetChange User Name and Password C. Enter a User Name and PasswordSet Self-Monitoring C. Enter the Master Administrator’s E-Mail AddressStep 3 R3000 Configuration D. Select 8e6 Enterprise Reporter, and then click SaveStep 4 Client Workstation Configuration Step 5 Launch the ER Client F. Enter the Password, and Confirm Password Conclusion Administrator Console, Expiration Screen Important Information about using the ER in the Evaluation ModeER Client, ER Server Statistics Window Specification Physical SpecificationsNon-“H” Server Specifications ValueER3-100 Hardware Component SpecificationsInternal Product Specifications ER3-200LED Indicators and Buttons Front Panel LED Indicators and ButtonsDiagrams and Descriptions LED Indicator KeyERH-200 Value “H” Server SpecificationsERH-100 Value Physical SpecificationsHardware Component Specifications ERH-100ERH-200 Internal Product SpecificationsFront of Chassis Control Panel Rear of Chassis Declaration of the Manufacturer or Importer Regulatory Specifications and DisclaimersSafety Compliance Electromagnetic Compatibility EMCChina Compulsory Certification CCC - China Electromagnetic Compatibility Class A NoticeIndustry Canada Equipment Standard for Digital Equipment ICES-003 8e6 Enterprise Reporter Quick Start GuideEuropean Community Directives Requirement CE EC Declaration of ConformityDeclaration of Conformity Appendix SCSI Connected Storage Device Preliminary Setup ProceduresOther Required Installation Items Unpack the Unit from the CartonRack Mount the Server Rack Setup PrecautionsRack Mount Components Appendix SAN Installation StepAttach inner slide rail to chassis using 3 screws as shown StepStep NOTE Make sure the flange is on the bottom edgeAttach left and right rear long extended brackets to the outer rail using 2 screws, 2 washers, and 2 nuts for each bracket StepStep Attach outer rail to chassis using 4 screws and cage nuts per rail, 2 at each endStep Install the Unit Link the ER Unit with the SCSI Connected DeviceShut Down the Storage Device Unit Shut Down, Restart ProceduresRestart the Storage Device Unit Appendix SAN Installation Physical Components8e6 Enterprise Reporter Quick Start Guide Power Supply Status Temperature and Ventilation StatusLED Display Silence Button Management AlarmDisc Drive Alarm Disk Drive ActivityTable 2 Hardware Component Specifications SpecificationsTable 1 Physical Specifications SATABoy Model ValueAppendix SAN Installation 8e6 Enterprise Reporter Quick Start GuideFax 714.282.6116 Sales/Technical Support 714.282.6117 General Office 8e6 Corporate Headquarters USA828 West Taft Avenue Orange, CA 92865-4232 Tel 714.282.6111 or Satellite Office