Manuals / 8e6 Technologies / Computer Equipment / Network Card

8e6 Technologies ERS-200 (5K02-52), ER3-100 (5K02-55) quick start HyperTerminal Setup Procedures

Models: ERH-200 (5K02-24) ER3-200 (5K02-56) ERS-100 (5K02-51) ERS-200 (5K02-52) ERH-100 (5K02-61) ER3-100 (5K02-55)

1 74

Download 74 pages 30.79 Kb

Page 27

HyperTerminal Setup Procedures

HyperTerminal Setup Procedures

If using a serial console, follow these procedures to create a HyperTerminal session.

A.Launch HyperTerminal by going to Start > Programs > Accessories > Communica- tions > HyperTerminal:

B.In the Connection Description dialog box, enter any session Name, and then click OK to open the Connect To dialog box:

8e6 Enterprise Reporter Quick Start Guide

23

Image 27

8e6 Technologies ERS-200 (5K02-52), ER3-100 (5K02-55), ER3-200 (5K02-56), ERH-100 (5K02-61) HyperTerminal Setup Procedures

Contents

Model ER Release 5.0.00 / UpdatedGUIDE QUICK STARTTrademarks 8e6 Enterprise Reporter Quick Start GuideInstall the Server ContentsService Information Preliminary Setup Procedures“H” Server Specifications Regulatory Specifications and DisclaimersAppendix SCSI Connected Storage Device ER Enterprise Reporter Introduction Conventions Used in this Document About this Document8e6 Taiwan Service InformationProcedures 8e6 Corporate Headquarters USAUnpack the Unit from the Carton Preliminary Setup ProceduresSelect a Site for the Server Inside front end of U-shaped Install the “H” Server BezelFront of bezel Outside of left inner railE. Take up the free end of the bezel and also the loosened inner rail G. Slide the inner rail forward beneath the clips to lock it in place Rack Mount the Server Rack Setup PrecautionsRack Setup Suggestions Rack Mount Instructions for non-“H” ServersIdentify the Sections of the Rack Rails Install the Rack Rails Install the Chassis RailsInstalling the Server into a Telco Rack Install the Server into the RackYou should have received two rack rail assemblies with the 8e6 server unit. Each of these assemblies consists of two sections An inner fixed chassis rail that secures to the unit A, and an outer fixed rack rail that secures directly to the rack itself B. Two pairs of short brackets to be used on the front side of the outer rails are also included Identify the Sections of the Rack RailsRack Setup Suggestions Install the Inner RailsInstall the Outer Rails Rack Mount Instructions for “H” Servers8e6 Enterprise Reporter Quick Start Guide Install the Server into the RackIf you are installing the 8e6 server unit into a Telco type rack, follow the directions given on the previous page for rack installation. The only difference in the installation proce- dure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the Telco rack Installing the Server into a Telco RackPower Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Administrator Console Setup Requirements Step 1 Setup ProceduresInstall the Server Quick Start Setup RequirementsSerial Console Setup Step 1A Quick Start Setup ProceduresStorage Device Setup for Attached Storage Units Monitor and Keyboard SetupHyperTerminal Setup Procedures 8e6 Enterprise Reporter Quick Start Guide D. Specify the following session settings Bits per second Data bitsParity None Stop bits Flow control Hardware E. Click OK to connect to the HyperTerminal sessionG. Click the Settings tab, and at the Emulation menu select “VT100” Quick Start menu screen Login screenQuick Start menu administration menu Log Off, Disconnect the Peripherals System Status screenStorage Device Setup for Attached Storage Units Step 1B Console Setup ProceduresPreliminary Setup Workstation ConfigurationsA. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 port Link the Workstation to the ERThe Boot Up Process Network Setup Access the InternetLog in to the Administrator Console Network Settings C. Click OK to go to the main screen of the Administrator console8e6 Enterprise Reporter Quick Start Guide G. Enter the Second DNS IP address of the fallback DNS Regional Setting Time Zone Regional Setting NTP Servers Regional Setting LanguagePhysically Connect the ER to the Network Access the Internet Step 2 Change User Name and Password, Set Self- MonitoringC. Enter a User Name and Password Change User Name and PasswordC. Enter the Master Administrator’s E-Mail Address Set Self-MonitoringD. Select 8e6 Enterprise Reporter, and then click Save Step 3 R3000 ConfigurationStep 4 Client Workstation Configuration Step 5 Launch the ER Client F. Enter the Password, and Confirm Password Conclusion Important Information about using the ER in the Evaluation Mode Administrator Console, Expiration ScreenER Client, ER Server Statistics Window Value Physical SpecificationsNon-“H” Server Specifications SpecificationER3-200 Hardware Component SpecificationsInternal Product Specifications ER3-100LED Indicator Key Front Panel LED Indicators and ButtonsDiagrams and Descriptions LED Indicators and ButtonsPhysical Specifications “H” Server SpecificationsERH-100 Value ERH-200 ValueInternal Product Specifications ERH-100ERH-200 Hardware Component SpecificationsFront of Chassis Control Panel Rear of Chassis Electromagnetic Compatibility EMC Regulatory Specifications and DisclaimersSafety Compliance Declaration of the Manufacturer or Importer8e6 Enterprise Reporter Quick Start Guide Electromagnetic Compatibility Class A NoticeIndustry Canada Equipment Standard for Digital Equipment ICES-003 China Compulsory Certification CCC - ChinaEC Declaration of Conformity European Community Directives Requirement CEDeclaration of Conformity Unpack the Unit from the Carton Preliminary Setup ProceduresOther Required Installation Items Appendix SCSI Connected Storage DeviceRack Setup Precautions Rack Mount the ServerRack Mount Components Step StepAttach inner slide rail to chassis using 3 screws as shown Appendix SAN InstallationStep NOTE Make sure the flange is on the bottom edgeAttach left and right rear long extended brackets to the outer rail using 2 screws, 2 washers, and 2 nuts for each bracket StepAttach outer rail to chassis using 4 screws and cage nuts per rail, 2 at each end StepStep Link the ER Unit with the SCSI Connected Device Install the UnitShut Down, Restart Procedures Shut Down the Storage Device UnitRestart the Storage Device Unit Physical Components Appendix SAN Installation8e6 Enterprise Reporter Quick Start Guide Temperature and Ventilation Status Power Supply StatusLED Display Disk Drive Activity Management AlarmDisc Drive Alarm Silence ButtonSATABoy Model Value SpecificationsTable 1 Physical Specifications Table 2 Hardware Component Specifications8e6 Enterprise Reporter Quick Start Guide Appendix SAN InstallationSatellite Office 8e6 Corporate Headquarters USA828 West Taft Avenue Orange, CA 92865-4232 Tel 714.282.6111 or Fax 714.282.6116 Sales/Technical Support 714.282.6117 General Office