Manuals / 8e6 Technologies / Computer Equipment / Network Card

8e6 Technologies ERH-100 (5K02-61), ER3-100 (5K02-55) Installing the Server into a Telco Rack

Models: ERH-200 (5K02-24) ER3-200 (5K02-56) ERS-100 (5K02-51) ERS-200 (5K02-52) ERH-100 (5K02-61) ER3-100 (5K02-55)

1 74

Download 74 pages 30.79 Kb

Page 20

Image 20

Installing the Server into a Telco Rack

If you are installing the 8e6 server unit into a Telco type rack, follow the directions given on the previous page for rack installation. The only difference in the installation proce- dure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the Telco rack.

16	8e6 Enterprise Reporter Quick Start Guide

Page 20

Image 20

8e6 Technologies ERH-100 (5K02-61), ER3-100 (5K02-55), ER3-200 (5K02-56) quick start Installing the Server into a Telco Rack

Contents

Release 5.0.00 / Updated GUIDEQUICK START Model ER8e6 Enterprise Reporter Quick Start Guide TrademarksContents Service InformationPreliminary Setup Procedures Install the ServerAppendix SCSI Connected Storage Device “H” Server SpecificationsRegulatory Specifications and Disclaimers ER Enterprise Reporter Introduction About this Document Conventions Used in this DocumentService Information Procedures8e6 Corporate Headquarters USA 8e6 TaiwanPreliminary Setup Procedures Unpack the Unit from the CartonSelect a Site for the Server Install the “H” Server Bezel Front of bezelOutside of left inner rail Inside front end of U-shapedE. Take up the free end of the bezel and also the loosened inner rail G. Slide the inner rail forward beneath the clips to lock it in place Rack Setup Precautions Rack Mount the ServerIdentify the Sections of the Rack Rails Rack Setup SuggestionsRack Mount Instructions for non-“H” Servers Install the Chassis Rails Install the Rack RailsInstall the Server into the Rack Installing the Server into a Telco RackIdentify the Sections of the Rack Rails You should have received two rack rail assemblies with the 8e6 server unit. Each of these assemblies consists of two sections An inner fixed chassis rail that secures to the unit A, and an outer fixed rack rail that secures directly to the rack itself B. Two pairs of short brackets to be used on the front side of the outer rails are also includedInstall the Inner Rails Install the Outer RailsRack Mount Instructions for “H” Servers Rack Setup SuggestionsInstall the Server into the Rack 8e6 Enterprise Reporter Quick Start GuideInstalling the Server into a Telco Rack If you are installing the 8e6 server unit into a Telco type rack, follow the directions given on the previous page for rack installation. The only difference in the installation proce- dure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the Telco rackCheck the Power Supply Power Supply PrecautionsGeneral Safety Information Server Operation and Maintenance PrecautionsAC Power Cord and Cable Precautions Electrical Safety PrecautionsMotherboard Battery Precautions Step 1 Setup Procedures Install the ServerQuick Start Setup Requirements Administrator Console Setup RequirementsStep 1A Quick Start Setup Procedures Storage Device Setup for Attached Storage UnitsMonitor and Keyboard Setup Serial Console SetupHyperTerminal Setup Procedures D. Specify the following session settings Bits per second Data bits Parity None Stop bits Flow control HardwareE. Click OK to connect to the HyperTerminal session 8e6 Enterprise Reporter Quick Start GuideG. Click the Settings tab, and at the Emulation menu select “VT100” Login screen Quick Start menu screenQuick Start menu administration menu System Status screen Log Off, Disconnect the PeripheralsStep 1B Console Setup Procedures Preliminary SetupWorkstation Configurations Storage Device Setup for Attached Storage UnitsLink the Workstation to the ER A. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 portThe Boot Up Process Log in to the Administrator Console Network SetupAccess the Internet 8e6 Enterprise Reporter Quick Start Guide Network SettingsC. Click OK to go to the main screen of the Administrator console G. Enter the Second DNS IP address of the fallback DNS Regional Setting Time Zone Regional Setting Language Regional Setting NTP ServersPhysically Connect the ER to the Network Step 2 Change User Name and Password, Set Self- Monitoring Access the InternetChange User Name and Password C. Enter a User Name and PasswordSet Self-Monitoring C. Enter the Master Administrator’s E-Mail AddressStep 3 R3000 Configuration D. Select 8e6 Enterprise Reporter, and then click SaveStep 4 Client Workstation Configuration Step 5 Launch the ER Client F. Enter the Password, and Confirm Password Conclusion Administrator Console, Expiration Screen Important Information about using the ER in the Evaluation ModeER Client, ER Server Statistics Window Physical Specifications Non-“H” Server SpecificationsSpecification ValueHardware Component Specifications Internal Product SpecificationsER3-100 ER3-200Front Panel LED Indicators and Buttons Diagrams and DescriptionsLED Indicators and Buttons LED Indicator Key“H” Server Specifications ERH-100 ValueERH-200 Value Physical SpecificationsERH-100 ERH-200Hardware Component Specifications Internal Product SpecificationsFront of Chassis Control Panel Rear of Chassis Regulatory Specifications and Disclaimers Safety ComplianceDeclaration of the Manufacturer or Importer Electromagnetic Compatibility EMCElectromagnetic Compatibility Class A Notice Industry Canada Equipment Standard for Digital Equipment ICES-003China Compulsory Certification CCC - China 8e6 Enterprise Reporter Quick Start GuideDeclaration of Conformity EC Declaration of ConformityEuropean Community Directives Requirement CE Preliminary Setup Procedures Other Required Installation ItemsAppendix SCSI Connected Storage Device Unpack the Unit from the CartonRack Mount Components Rack Setup PrecautionsRack Mount the Server Step Attach inner slide rail to chassis using 3 screws as shownAppendix SAN Installation StepNOTE Make sure the flange is on the bottom edge Attach left and right rear long extended brackets to the outer rail using 2 screws, 2 washers, and 2 nuts for each bracketStep StepStep Attach outer rail to chassis using 4 screws and cage nuts per rail, 2 at each endStep Install the Unit Link the ER Unit with the SCSI Connected DeviceRestart the Storage Device Unit Shut Down, Restart ProceduresShut Down the Storage Device Unit 8e6 Enterprise Reporter Quick Start Guide Physical ComponentsAppendix SAN Installation LED Display Temperature and Ventilation StatusPower Supply Status Management Alarm Disc Drive AlarmSilence Button Disk Drive ActivitySpecifications Table 1 Physical SpecificationsTable 2 Hardware Component Specifications SATABoy Model ValueAppendix SAN Installation 8e6 Enterprise Reporter Quick Start Guide8e6 Corporate Headquarters USA 828 West Taft Avenue Orange, CA 92865-4232 Tel 714.282.6111 orFax 714.282.6116 Sales/Technical Support 714.282.6117 General Office Satellite Office