Manuals / 8e6 Technologies / Computer Equipment / Network Card

8e6 Technologies ER3-200 (5K02-56) “H” Server Specifications, ERH-100 Value, ERH-200 Value

Models: ERH-200 (5K02-24) ER3-200 (5K02-56) ERS-100 (5K02-51) ERS-200 (5K02-52) ERH-100 (5K02-61) ER3-100 (5K02-55)

1 74

Download 74 pages 30.79 Kb

Page 55

“H” Server Specifications

“H” Server Specifications

Physical Specifications

Specification	ERH-100 Value	ERH-200 Value
Height	1.7” (43mm)	1.7” (43mm)
Width	17.2” (438mm)	17.2” (438mm)
Depth	26.8” (681mm)	26.8” (681mm)
Front clearance	2 inches (76mm)	2 inches (76mm)
Side clearance	1 inch (25mm)	1 inch (25mm)
Rear clearance	3.6 inches (92mm)	3.6 inches (92mm)
Weight	43.0 lbs (19.5 kg)	44.0 lbs (19.96 kg)

8e6 Enterprise Reporter Quick Start Guide

51

Image 55

8e6 Technologies ER3-200 (5K02-56) “H” Server Specifications, ERH-100 Value, ERH-200 Value, Physical Specifications

Contents

Model ER Release 5.0.00 / UpdatedGUIDE QUICK STARTTrademarks 8e6 Enterprise Reporter Quick Start GuideInstall the Server ContentsService Information Preliminary Setup ProceduresRegulatory Specifications and Disclaimers “H” Server SpecificationsAppendix SCSI Connected Storage Device ER Enterprise Reporter Introduction Conventions Used in this Document About this Document8e6 Taiwan Service InformationProcedures 8e6 Corporate Headquarters USAUnpack the Unit from the Carton Preliminary Setup ProceduresSelect a Site for the Server Inside front end of U-shaped Install the “H” Server BezelFront of bezel Outside of left inner railE. Take up the free end of the bezel and also the loosened inner rail G. Slide the inner rail forward beneath the clips to lock it in place Rack Mount the Server Rack Setup PrecautionsRack Mount Instructions for non-“H” Servers Rack Setup SuggestionsIdentify the Sections of the Rack Rails Install the Rack Rails Install the Chassis RailsInstalling the Server into a Telco Rack Install the Server into the RackYou should have received two rack rail assemblies with the 8e6 server unit. Each of these assemblies consists of two sections An inner fixed chassis rail that secures to the unit A, and an outer fixed rack rail that secures directly to the rack itself B. Two pairs of short brackets to be used on the front side of the outer rails are also included Identify the Sections of the Rack RailsRack Setup Suggestions Install the Inner RailsInstall the Outer Rails Rack Mount Instructions for “H” Servers8e6 Enterprise Reporter Quick Start Guide Install the Server into the RackIf you are installing the 8e6 server unit into a Telco type rack, follow the directions given on the previous page for rack installation. The only difference in the installation proce- dure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accommodate the width of the Telco rack Installing the Server into a Telco RackPower Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Administrator Console Setup Requirements Step 1 Setup ProceduresInstall the Server Quick Start Setup RequirementsSerial Console Setup Step 1A Quick Start Setup ProceduresStorage Device Setup for Attached Storage Units Monitor and Keyboard SetupHyperTerminal Setup Procedures 8e6 Enterprise Reporter Quick Start Guide D. Specify the following session settings Bits per second Data bitsParity None Stop bits Flow control Hardware E. Click OK to connect to the HyperTerminal sessionG. Click the Settings tab, and at the Emulation menu select “VT100” Quick Start menu screen Login screenQuick Start menu administration menu Log Off, Disconnect the Peripherals System Status screenStorage Device Setup for Attached Storage Units Step 1B Console Setup ProceduresPreliminary Setup Workstation ConfigurationsA. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 port Link the Workstation to the ERThe Boot Up Process Access the Internet Network SetupLog in to the Administrator Console C. Click OK to go to the main screen of the Administrator console Network Settings8e6 Enterprise Reporter Quick Start Guide G. Enter the Second DNS IP address of the fallback DNS Regional Setting Time Zone Regional Setting NTP Servers Regional Setting LanguagePhysically Connect the ER to the Network Access the Internet Step 2 Change User Name and Password, Set Self- MonitoringC. Enter a User Name and Password Change User Name and PasswordC. Enter the Master Administrator’s E-Mail Address Set Self-MonitoringD. Select 8e6 Enterprise Reporter, and then click Save Step 3 R3000 ConfigurationStep 4 Client Workstation Configuration Step 5 Launch the ER Client F. Enter the Password, and Confirm Password Conclusion Important Information about using the ER in the Evaluation Mode Administrator Console, Expiration ScreenER Client, ER Server Statistics Window Value Physical SpecificationsNon-“H” Server Specifications SpecificationER3-200 Hardware Component SpecificationsInternal Product Specifications ER3-100LED Indicator Key Front Panel LED Indicators and ButtonsDiagrams and Descriptions LED Indicators and ButtonsPhysical Specifications “H” Server SpecificationsERH-100 Value ERH-200 ValueInternal Product Specifications ERH-100ERH-200 Hardware Component SpecificationsFront of Chassis Control Panel Rear of Chassis Electromagnetic Compatibility EMC Regulatory Specifications and DisclaimersSafety Compliance Declaration of the Manufacturer or Importer8e6 Enterprise Reporter Quick Start Guide Electromagnetic Compatibility Class A NoticeIndustry Canada Equipment Standard for Digital Equipment ICES-003 China Compulsory Certification CCC - ChinaEuropean Community Directives Requirement CE EC Declaration of ConformityDeclaration of Conformity Unpack the Unit from the Carton Preliminary Setup ProceduresOther Required Installation Items Appendix SCSI Connected Storage DeviceRack Mount the Server Rack Setup PrecautionsRack Mount Components Step StepAttach inner slide rail to chassis using 3 screws as shown Appendix SAN InstallationStep NOTE Make sure the flange is on the bottom edgeAttach left and right rear long extended brackets to the outer rail using 2 screws, 2 washers, and 2 nuts for each bracket StepStep Attach outer rail to chassis using 4 screws and cage nuts per rail, 2 at each endStep Link the ER Unit with the SCSI Connected Device Install the UnitShut Down the Storage Device Unit Shut Down, Restart ProceduresRestart the Storage Device Unit Appendix SAN Installation Physical Components8e6 Enterprise Reporter Quick Start Guide Power Supply Status Temperature and Ventilation StatusLED Display Disk Drive Activity Management AlarmDisc Drive Alarm Silence ButtonSATABoy Model Value SpecificationsTable 1 Physical Specifications Table 2 Hardware Component Specifications8e6 Enterprise Reporter Quick Start Guide Appendix SAN InstallationSatellite Office 8e6 Corporate Headquarters USA828 West Taft Avenue Orange, CA 92865-4232 Tel 714.282.6111 or Fax 714.282.6116 Sales/Technical Support 714.282.6117 General Office