ADIC FastStor Mass Storage Device eject slot , SRC slot n

Operation and Maintenance 25

Mode 3 – EJECT SLOT

Mode 3 causes the FastStor to move a tape from slot 6 to slot 1, or from slot 7 to slot 2.

Note

If the source slot is empty, or the destination slot is full, selecting EJECT SLOT will cause a blinking RESELECT to appear on the

LCD. The blinking RESELECT indicates that you attempted to select an invalid mode.

❐ To access Mode 3, press the MODE button until the LCD appears as shown:

eject slot

2 3 4 5 6 7

❐ Press the SELECT button to select Mode 3. The LCD will appear as shown (N is either 6 or 7):

SRC slot n

2 3 4 5 6 7

❐ Press the NEXT or PREVIOUS button to scroll to choose slot 6 or 7 to eject.

❐ Press select when the slot you wish to eject is displayed. The FastStor will move the tape from the source slot to the

appropriate destination slot.

Note

EJECT SLOT always moves the tape in slot 6 to slot 1, and slot 7 to slot 2.

When your FastStor has completed the command, it will return to LdR REAdY.

Contents

Main Copyright Notice Copyright Notice (Europe) Regulatory Notices FCC Notices (USA Only) IC Notice (Canada Only) EN 55022 Compliance (Czech Republic Only) CE Notice VCCI Notices (Japan Only) DECLARATION OF CONFORMITY according to EN 45014 Safety Notices Warnings A C UTION Page Table of Contents Page Page Page Page Page Page Page Page W Equipment Description Features DLT Drives Options SCSI Interface Switches and Indicators Page DC WP CT 5 1 2 3 4 5 6 7 Page DLT Media Other Requirements Page Unpacking and Inspecting Checking the Accessories Installing the Host Adapter Installing the SCSI Cable and Terminator Connecting More than One FastStor Preparing the Host Computer System Installing the Application Software Page Normal Operations General Guidelines Powering on the System L r init rv init L r rea y Setting the SCSI IDs Page Prepare and Install the Data Cartridges Close and Lock the Front Door Drive Status Messages FastStor Modes Mode 1A LOAD DRV Loa rv SRC slot L r rea y Mode 1B EJECT DRV eject rv ejecting L r rea y Mode 2 LOAD SLOT loa slot SRC slot N Mode 3 EJECT SLOT eject slot SRC slot n Mode 4 EJECT PCKR eject pckr st slot n Mode 5 DENSITY ensity 1 2 3 4 5 6 7 Fmt XX Set scsi L r scsi L r I x rv scsi rv I x Cycle pwr Normal Maintenance Cleaning the Drive Head Cleaning Tape Drive Head Cleaning Procedure Manually Cleaning the Drive Head Page Page Installation Problems Loader and Drive Operational Problems DIAGNOSTIC MENU iag menu DISPLAY FIRMWARE sp fw sp l r fw l fw NNNN sp rv fw r fw NNNN sp mtn fw mtn fw NN sp fp fw fp fw NNNN sp T fw t fw NNNN SIGN ON Sign on CHANGE MODE Chg mo e 2 3 4 5 6 7 CYCLE TEST Cycle TEST CycleS CLEAN DRIVE CLEAN RV Ct 2 (Sel) Cleaning RMV 2 (Sel) AUTOCLEAN AUTOCLEAN AC oN CT 2 (SEL) Using AUTOCLEAN CYCLE AC 7 3 4 5 6 Disabling AUTOCLEAN AC OFF RMV 2 (SEL) LOAD FIRMWARE DISPLAY COUNTS SP cOUNTS frt pk ct (000000XX) UPGRADE DRIVE FIRMWARE UPG rv fw Ct 2 (sel) Rmv 2 (sel) 1 2 34567 FastStor Error Messages Error Message Listing Environmental Considerations When You Call ADICS Technical Assistance Center