Unit Access Table Commands, Command What it does | ADTRAN TDU 120e

Chapter 8. Remote/Management Menus

	The following chart describes each command of the Unit
	Access Table.
	Table 8-1. Unit Access Table Commands

Command	What it does...


Add New Unit	Adds a new device to the table.
	You must enter a device Unit ID, passcode, Unit type, and polled
	flag. Unit type can be:
	Standard (which supports any TSU/TDU Multiplexer and the ISU
	512), or TSU Standalone (a single port TSU with no option card slot).
	A passcode of 0 to 9999 for each device or DEFAULT may be
	selected, which results in the default passcode being used (defined
	as 0022 in Figure 8-1 on page 8-2).
	Traps are normally sent from the unit in alarm to the TDU 120e. For
	units in the Unit Access Table that are not chained directly to the
	TDU 120e but are managed over Inband or the FDL, traps are not
	automatically forwarded. Polling must be enabled on the TDU 120e
	for these units in order to receive Traps on the NMS. The TDU 120e
	can be configured to poll selected units for traps by enabling the
	polled option when adding or modifying a unit entry.

Modify Unit	Allows unit ID, passcode, device type, and polled flag to be changed
	for an existing entry in the table.

Delete Unit	Deletes an entry in the table.

Default Unit	Sets the default passcode for all devices in the table that have
Passcode	passcodes set to DEFAULT, or for any unit not listed in the table.

OK	Returns to the CONFIGURE AGENT menu.

61202156L2-1A

TDU 120e User Manual

8-3

Image 111

ADTRAN TDU 120e user manual Unit Access Table Commands, Command What it does

Contents

TDU 120e Trademarks Important Safety Instructions Save These Important Safety Instructions REN/SOC FIC Usoc Affidavit Requirements for Connection to Digital Services Page Vii Canadian Emissions Requirements Canadian Equipment Limitations Limited Product Warranty Customer Service, Product Support Information, and Training Presales Inquiries and Applications SupportPost-Sale Support Training Repair and Return Table of Contents Operation Status Menu Configuration Menu Port Configuration Port Config Nx/DBU 0.1 Menu Items Remote/Management Menus Xmodem Table of Contents Bridge, PBX, Video Conferencing Application Set-up List of Figures List of Figures Xxii List of Tables List of Tables Xxiv TDU 120e Overview Introduction Introduction Standard Features in the TDU 120e DSU DP TDU 120e Option ModulesDSX-1 OCU DP TDU 120e Option Modules Option Module Architecture Router, PBX, Video Conferencing Application TDU 120e Configuration Applications Adtran Shipments InstallationUNPACK, INSPECT, Power UP Receipt Inspection Customer Provides Power ConnectionAC Powered Units DC Powered Units Grounding Instructions Installation TDU 120e Rear Panels Identification of Rear Panel Layout Network Interface TDU 120e Interfaces Craft Port External Alarm ConnectorDS-1 PBX Interface Control In Port Self-Test Power UP Testing Set Control Port InitializationSet User Passcode Set Unit Identification Chain In/Chain Out Chain In PC Normal POWER-UP Procedure Installation Menu Operation Operation Select and Activate a Menu Item Sample Terminal Screen with TDU 120e MenuGeneral Menu Traversal Main Menu Example of Basic Menu Travel Step Action Result Data Port Identification Edit the Data FieldExit Any Menu Field Operation or Display Telnet/Terminal Main Menu Menu Structure Menu Options Quit Session Management ConfigurationFront Panel Flash Download Network Monitor Jack ACO SwitchRemote LED Craft Port LED LEDs Port Status LEDs Port 1.1 Option Card Monitor Jacks Step Action Setting up the TDU 120e to Work over a LANAlternate Methods of Control Watch PRO Adtran PC Program Snmp Setting up the TDU 120e to Work over an EIA-232 Connection Status Status Menu UAS Where MeansNetwork NI Performance Reports SES Active Alarms Network Interface NI Errors Port Status View History Nx/DBU 0.1 Menu Items DTE Data/Clock DTE StatusDTE Port Rate DBU Data/CNTRL DBU ControlDBU Status DS-1 0.2 Menu Items DS-1 Errors Remote PortSlip CPU Clear Port AlarmEthernet Status LNK Config Configuration Menu TDU 120e Config Menu Tree Network NI Menu Tree Unit Menu Tree Network NI Menu Items Network NI Timing Mode Network Timed Clock Source Network Timed Base DS-1 Timed Clock Source Base DS-1 Base DTE Timed Clock Source Base DTE Timing Internal Clock Source Internal Timing Secondary Clock Source Secondary Timing Normal CSU Normal CSU Timing ATT & FT1, Reject ALL Alarm Report Exit Alarm FormatUnit Menu BPV Threshold Subnet Address Default RouterControl Port IP Address Map Exchange OFFAuto DS0 Map B Map In UseDS0 Map a and DS0 Map B DS0 Map a 10. DS0 Temp Map DS0 Maps Configuration Menu If you want to Enter selections Creating a DSO MapStep Explanation Initializing the Temp Map Copying Map Editing the Temp MapStep Action Explanation Applying the Temp Map Reviewing Maps Copy Map a B to Temp MapCreate Temp Map Edit Temp Map Port Configuration Port ConfigReview Map a B Review Temp Map Nx/DBU 0.1 Menu Items Nx56/64 Config Inhib Backup On Normal Mode of OperationDial Backup Config Backup Mode Pattern Verify Backup DelayRestore Delay Retry Delay Wkend Lockout Backup Testing DS-1 0.2 Menu Items Trap in DBUInband Lpback Robbed Bit Signaling RBS StartRBS End Configuration Menu Util Utility Menu Press Escape Factory RestoreTime/Date If you want to Do this Lost Passcode Set PasscodeUnit ID Change/Set a Passcode To Set the Unit Identification Software RevisionPort Utility MAC Address Test Test Menu Loopback Tests Network Tests TDU 120e Ansi FDL PLB Ansi FDL LLBAnsi FT1 LLB Qrss All DS0s Test Patterns All OnesAll Zeros Qrss Pattern Pattern Result Qrss TST DS0sNone Instructions for Generating a Qrss Test Pattern Step Action Sync How to Run an End-to-End Test on Fractional DS0s Step Action Test Name What it does Run Self-Test DTE Loopback Port Tests DBU Loopback REM V.54Pattrn Results Port Loopback Cancel TestsDBU DATA/CNTRL DBU TST Result Test Menu Remote Menu Access Management ConfigurationRemote/Management Menus Unit Access Table Unit Access Table Command What it does Unit Access Table Commands Host 1 Trap IP Address Snmp Read CommunitySnmp Read/Write Community Snmp Trap Community System Name Host 2 Trap IP AddressHost 3 Trap IP Address Host 4 Trap IP Address Xmodem Flash Download Tftp Server File name T120e.biz Begin Firmware updateQuit Session Tftp Server IP Address Remote/Management Menus Network Manager What is SNMP?Appendix a Understanding Snmp Basic Components of Snmp GetNextRequest CommandsMIB GetRequest Message GetResponseTrap TDU 120e Snmp Access Snmp Trap Configuration RFC1406.MIB Snmp MIB Browser Configuration Snmp MIB Files Appendix A. Understanding Snmp Appendix B Connector Pinouts WiringNetwork Pin Name Description Control In/Chain Table B-4. Chain-Out Pinout Control-Out/Chain-Out Table B-5. Craft Port Pinout Nx56/64 DTE Table B-6. V.35 Pinout for Nx56/64 DTEPin Base DS-1 PBX 12,13,14,15 Alarm Power10BaseT Nx/DBU Interface Alarm MessagesAppendix C System Messages Network Interface NI DS-1 PBX Interface PLL AlarmZeros Alarm Fifo Alarm Status Messages Port Loop Up Pattern OffFrame Slip Line Loop Up Appendix D Specifications Electrical SpecificationsT1/FT1 Interface CTS, DCD, DSR Nx/DBU Interface Port 0.1-Nx56/64 V.35 Interface DS-1 Interface Port Management Interfaces Rate ReceiverOption Slot Interface Environmental Specifications Chassis Specification Numerics Index Index 61202156L2-1 Index-3 Index-4