Sync | ADTRAN TDU 120e specs

Chapter 7. Test Menu

SES

The number of seconds with more than 320 bit errors.

*SYNC

Indicates if pattern sync is (YES) or is not (NO) valid. The asterisk (*) indicates if pattern sync has been lost since the start of testing.

Clear results by pressing C. The results are accumulated until the test pattern is set to NONE or CLEARED.

Using TST DS0s for testing can be very useful, particu- larly in Fractional T1 applications.

How to Run an End-to-End Test on Fractional DS0s

Step

Action

1Set the TST for Map B in the same DS0 as used by Map A to receive data from an Nx56/64 port.

2Loop the far end using a V.54 loopback code on the Nx56/64 port.

A single DS0 can be used for continuous testing while other DS0s are passing normal data. This will also provide an end-to-end check on the entire link. Set each end to send QRSS in TST DS0s (using 1 DS0) and occasionally view the results on the Pattern Result menu selection.

61202156L2-1

TDU 120e User Manual

7-7

Image 103

ADTRAN TDU 120e user manual Sync, How to Run an End-to-End Test on Fractional DS0s Step Action

Contents

TDU 120e Trademarks Important Safety Instructions Save These Important Safety Instructions REN/SOC FIC Usoc Affidavit Requirements for Connection to Digital Services Page Vii Canadian Emissions Requirements Canadian Equipment Limitations Limited Product Warranty Presales Inquiries and Applications Support Customer Service, Product Support Information, and TrainingPost-Sale Support Training Repair and Return Table of Contents Operation Status Menu Configuration Menu Port Configuration Port Config Nx/DBU 0.1 Menu Items Remote/Management Menus Xmodem Table of Contents Bridge, PBX, Video Conferencing Application Set-up List of Figures List of Figures Xxii List of Tables List of Tables Xxiv TDU 120e Overview Introduction Introduction Standard Features in the TDU 120e DSU DP TDU 120e Option ModulesDSX-1 OCU DP TDU 120e Option Modules Option Module Architecture Router, PBX, Video Conferencing Application TDU 120e Configuration Applications Adtran Shipments InstallationUNPACK, INSPECT, Power UP Receipt Inspection Customer Provides Power ConnectionAC Powered Units DC Powered Units Grounding Instructions Installation TDU 120e Rear Panels Identification of Rear Panel Layout Network Interface TDU 120e Interfaces Craft Port External Alarm ConnectorDS-1 PBX Interface Control In Port Self-Test Power UP Testing Set Control Port InitializationSet User Passcode Set Unit Identification Chain In/Chain Out Chain In PC Normal POWER-UP Procedure Installation Menu Operation Operation Select and Activate a Menu Item Sample Terminal Screen with TDU 120e MenuGeneral Menu Traversal Main Menu Example of Basic Menu Travel Step Action Result Edit the Data Field Data Port IdentificationExit Any Menu Field Operation or Display Telnet/Terminal Main Menu Menu Structure Menu Options Quit Session Management ConfigurationFront Panel Flash Download Network Monitor Jack ACO SwitchRemote LED Craft Port LED LEDs Port Status LEDs Port 1.1 Option Card Monitor Jacks Step Action Setting up the TDU 120e to Work over a LANAlternate Methods of Control Watch PRO Adtran PC Program Snmp Setting up the TDU 120e to Work over an EIA-232 Connection Status Status Menu UAS Where MeansNetwork NI Performance Reports SES Active Alarms Network Interface NI Errors Port Status View History DTE Status Nx/DBU 0.1 Menu Items DTE Data/ClockDTE Port Rate DBU Control DBU Data/CNTRLDBU Status Remote Port DS-1 0.2 Menu Items DS-1 ErrorsSlip CPU Clear Port AlarmEthernet Status LNK Config Configuration Menu TDU 120e Config Menu Tree Network NI Menu Tree Unit Menu Tree Network NI Menu Items Network NI Timing Mode Network Timed Clock Source Network Timed Base DS-1 Timed Clock Source Base DS-1 Base DTE Timed Clock Source Base DTE Timing Internal Clock Source Internal Timing Secondary Clock Source Secondary Timing Normal CSU Normal CSU Timing ATT & FT1, Reject ALL Alarm Report Exit Alarm FormatUnit Menu BPV Threshold Subnet Address Default RouterControl Port IP Address OFF Map ExchangeAuto DS0 Map B Map In UseDS0 Map a and DS0 Map B DS0 Map a 10. DS0 Temp Map DS0 Maps Configuration Menu If you want to Enter selections Creating a DSO MapStep Explanation Initializing the Temp Map Copying Map Editing the Temp MapStep Action Explanation Applying the Temp Map Copy Map a B to Temp Map Reviewing MapsCreate Temp Map Edit Temp Map Port Configuration Port ConfigReview Map a B Review Temp Map Nx/DBU 0.1 Menu Items Nx56/64 Config Inhib Backup On Normal Mode of OperationDial Backup Config Backup Mode Pattern Verify Backup DelayRestore Delay Retry Delay Wkend Lockout Backup Testing Trap in DBU DS-1 0.2 Menu ItemsInband Lpback RBS Start Robbed Bit SignalingRBS End Configuration Menu Util Utility Menu Press Escape Factory RestoreTime/Date If you want to Do this Lost Passcode Set PasscodeUnit ID Change/Set a Passcode To Set the Unit Identification Software RevisionPort Utility MAC Address Test Test Menu Loopback Tests Network Tests TDU 120e Ansi FDL LLB Ansi FDL PLBAnsi FT1 LLB Qrss All DS0s Test Patterns All OnesAll Zeros Qrss Pattern Pattern Result Qrss TST DS0sNone Instructions for Generating a Qrss Test Pattern Step Action Sync How to Run an End-to-End Test on Fractional DS0s Step Action Test Name What it does Run Self-Test DTE Loopback Port Tests DBU Loopback REM V.54Pattrn Results Port Loopback Cancel TestsDBU DATA/CNTRL DBU TST Result Test Menu Management Configuration Remote Menu AccessRemote/Management Menus Unit Access Table Unit Access Table Command What it does Unit Access Table Commands Host 1 Trap IP Address Snmp Read CommunitySnmp Read/Write Community Snmp Trap Community System Name Host 2 Trap IP AddressHost 3 Trap IP Address Host 4 Trap IP Address Xmodem Flash Download Tftp Server File name T120e.biz Begin Firmware updateQuit Session Tftp Server IP Address Remote/Management Menus Network Manager What is SNMP?Appendix a Understanding Snmp Basic Components of Snmp GetNextRequest CommandsMIB GetRequest GetResponse MessageTrap TDU 120e Snmp Access Snmp Trap Configuration RFC1406.MIB Snmp MIB Browser Configuration Snmp MIB Files Appendix A. Understanding Snmp Wiring Appendix B Connector PinoutsNetwork Pin Name Description Control In/Chain Table B-4. Chain-Out Pinout Control-Out/Chain-Out Table B-5. Craft Port Pinout Table B-6. V.35 Pinout for Nx56/64 DTE Nx56/64 DTEPin Base DS-1 PBX 12,13,14,15 Power Alarm10BaseT Nx/DBU Interface Alarm MessagesAppendix C System Messages Network Interface NI DS-1 PBX Interface PLL AlarmZeros Alarm Fifo Alarm Status Messages Port Loop Up Pattern OffFrame Slip Line Loop Up Electrical Specifications Appendix D SpecificationsT1/FT1 Interface CTS, DCD, DSR Nx/DBU Interface Port 0.1-Nx56/64 V.35 Interface DS-1 Interface Port Management Interfaces Receiver RateOption Slot Interface Environmental Specifications Chassis Specification Numerics Index Index 61202156L2-1 Index-3 Index-4