TDU 120e Interfaces, Network Interface | ADTRAN instruction

Chapter 2. Installation

TDU 120e Interfaces

The TDU 120e rear panel is equipped with an Nx/DBU data port, a DS-1 interface, an option slot, management interfaces, an external alarm connector, and a T1 interface. See Figure 2-2.

	10BaseT
PC or Modem
	Control	Chain		Chain	Chain
	Input	Output		Input	Output
	NI TDU 120e			NI TDU 120e
Network	DS-1			DS-1
	Nx56/64 Option			Nx56/64 Option
PBX	V.35		DS-1	V.35
			Figure 2-2. TDU 120e Interfaces

Network Interface

The Network Interface (NI) port provides the connection to the T1. This port complies with the applicable ANSI and AT&T standards. For more information see Appendix B.

Nx56/64 Serial Interface

The Nx56/64 provides a serial V.35 port that operates from 56 kbps to 1.536 Mbps. This port provides 511 pat- tern generation and detection and remote loopback capa- bility.

2-6

TDU 120e User Manual

61202156L2-1

Image 36

ADTRAN user manual TDU 120e Interfaces, Network Interface

Contents

TDU 120e Trademarks Save These Important Safety Instructions Important Safety Instructions REN/SOC FIC Usoc Affidavit Requirements for Connection to Digital Services Page Vii Canadian Emissions Requirements Canadian Equipment Limitations Limited Product Warranty Customer Service, Product Support Information, and Training Presales Inquiries and Applications SupportPost-Sale Support Repair and Return Training Table of Contents Operation Status Menu Configuration Menu Port Configuration Port Config Nx/DBU 0.1 Menu Items Remote/Management Menus Xmodem Table of Contents List of Figures Bridge, PBX, Video Conferencing Application Set-up List of Figures Xxii List of Tables List of Tables Xxiv Introduction TDU 120e Overview Introduction Standard Features in the TDU 120e TDU 120e Option Modules DSX-1OCU DP DSU DP Option Module Architecture TDU 120e Option Modules TDU 120e Configuration Applications Router, PBX, Video Conferencing Application Installation UNPACK, INSPECT, Power UPReceipt Inspection Adtran Shipments Power Connection AC Powered UnitsDC Powered Units Customer Provides Grounding Instructions Installation Identification of Rear Panel Layout TDU 120e Rear Panels TDU 120e Interfaces Network Interface External Alarm Connector DS-1 PBX InterfaceControl In Port Craft Port Power UP Testing Self-Test Initialization Set User PasscodeSet Unit Identification Set Control Port Chain In PC Chain In/Chain Out Normal POWER-UP Procedure Installation Operation Menu Operation Sample Terminal Screen with TDU 120e Menu General Menu TraversalMain Menu Select and Activate a Menu Item Step Action Result Example of Basic Menu Travel Data Port Identification Edit the Data FieldExit Any Menu Field Operation or Display Menu Structure Telnet/Terminal Main Menu Menu Options Management Configuration Front PanelFlash Download Quit Session ACO Switch Remote LEDCraft Port Network Monitor Jack LEDs LED Port 1.1 Option Card Monitor Jacks Port Status LEDs Setting up the TDU 120e to Work over a LAN Alternate Methods of ControlWatch PRO Adtran PC Program Step Action Setting up the TDU 120e to Work over an EIA-232 Connection Snmp Status Menu Status Where Means Network NI Performance ReportsSES UAS Network Interface NI Errors Active Alarms View History Port Status Nx/DBU 0.1 Menu Items DTE Data/Clock DTE StatusDTE Port Rate DBU Data/CNTRL DBU ControlDBU Status DS-1 0.2 Menu Items DS-1 Errors Remote PortSlip Clear Port Alarm Ethernet StatusLNK CPU Configuration Menu Config TDU 120e Config Menu Tree Network NI Menu Tree Unit Menu Tree Network NI Network NI Menu Items Timing Mode Network Timed Network Timed Clock Source Base DS-1 Base DS-1 Timed Clock Source Base DTE Timing Base DTE Timed Clock Source Internal Timing Internal Clock Source Secondary Timing Secondary Clock Source Normal CSU Timing Normal CSU Alarm Report ATT & FT1, Reject ALL Alarm Format Unit MenuBPV Threshold Exit Default Router Control PortIP Address Subnet Address Map Exchange OFFAuto Map In Use DS0 Map a and DS0 Map BDS0 Map a DS0 Map B DS0 Maps Configuration Menu 10. DS0 Temp Map Creating a DSO Map Step ExplanationInitializing the Temp Map If you want to Enter selections Editing the Temp Map Step Action ExplanationApplying the Temp Map Copying Map Reviewing Maps Copy Map a B to Temp MapCreate Temp Map Port Configuration Port Config Review Map a BReview Temp Map Edit Temp Map Nx56/64 Config Nx/DBU 0.1 Menu Items Inhib Normal Mode of Operation Dial Backup ConfigBackup Mode Backup On Backup Delay Restore DelayRetry Delay Pattern Verify Backup Testing Wkend Lockout DS-1 0.2 Menu Items Trap in DBUInband Lpback Robbed Bit Signaling RBS StartRBS End Configuration Menu Utility Menu Util Factory Restore Time/DateIf you want to Do this Press Escape Set Passcode Unit IDChange/Set a Passcode Lost Passcode Software Revision Port UtilityMAC Address To Set the Unit Identification Test Menu Test Network Tests Loopback Tests TDU 120e Ansi FDL PLB Ansi FDL LLBAnsi FT1 LLB Test Patterns All Ones All ZerosQrss Pattern Qrss All DS0s Qrss TST DS0s NoneInstructions for Generating a Qrss Test Pattern Step Action Pattern Result How to Run an End-to-End Test on Fractional DS0s Step Action Sync Run Self-Test Test Name What it does Port Tests DTE Loopback REM V.54 PattrnResults DBU Loopback Cancel Tests DBU DATA/CNTRLDBU TST Result Port Loopback Test Menu Remote Menu Access Management ConfigurationRemote/Management Menus Unit Access Table Unit Access Table Unit Access Table Commands Command What it does Snmp Read Community Snmp Read/Write CommunitySnmp Trap Community Host 1 Trap IP Address Host 2 Trap IP Address Host 3 Trap IP AddressHost 4 Trap IP Address System Name Flash Download Xmodem Begin Firmware update Quit SessionTftp Server IP Address Tftp Server File name T120e.biz Remote/Management Menus What is SNMP? Appendix a Understanding SnmpBasic Components of Snmp Network Manager Commands MIBGetRequest GetNextRequest Message GetResponseTrap TDU 120e Snmp Access Snmp Trap Configuration Snmp MIB Browser Configuration RFC1406.MIB Snmp MIB Files Appendix A. Understanding Snmp Appendix B Connector Pinouts WiringNetwork Control In/Chain Pin Name Description Control-Out/Chain-Out Table B-4. Chain-Out Pinout Table B-5. Craft Port Pinout Nx56/64 DTE Table B-6. V.35 Pinout for Nx56/64 DTEPin Base DS-1 PBX 12,13,14,15 Alarm Power10BaseT Alarm Messages Appendix C System MessagesNetwork Interface NI Nx/DBU Interface PLL Alarm Zeros AlarmFifo Alarm DS-1 PBX Interface Status Messages Pattern Off Frame SlipLine Loop Up Port Loop Up Appendix D Specifications Electrical SpecificationsT1/FT1 Interface Nx/DBU Interface Port 0.1-Nx56/64 V.35 Interface CTS, DCD, DSR DS-1 Interface Port Management Interfaces Rate ReceiverOption Slot Interface Chassis Specification Environmental Specifications Index Numerics Index 61202156L2-1 Index-3 Index-4