Nx/DBU 0.1 Menu Items, Nx56/64 Config | ADTRAN TDU 120e manual

or INVERT

Chapter 5. Configuration Menu

The CONFIG menus for options ports are described in sep- arate sections of the manual supplied with the option card.

Nx/DBU (0.1) Menu Items

The Nx/DBU port has two main menus:

NX56/64 CONFIG -- Nx operation and DBU CONFIG -- DBU operation.

Nx56/64 Config

Under NX56/64 CONFIG, the menu items are:

DS0 RATE

This sets the base DS0 rate of the interface. The actual data rate depends on the number of DS0s assigned to the Nx port.

Choices: 56K OR 64K

TX CLK CNTRL

Controls the clock used by the TDU 120e to accept transmit (TX) data from the DTE. The default is NORMAL. If the interface cable is long, causing a phase shift in the data, the clock can be selected as INVERT. This switches the phase of the clock which should compensate for a long cable.

Choices: NORMAL, INVERT

DATA

Used to control the inverting of the DTE data. This inversion can be useful when operating with an HDLC protocol. Often used as a means to ensure 1s density.

Choices: NORMAL

If INVERT is selected, zero (0) inhibit should also be selected to prevent an open DTE input from placing zeros on the network.

61202156L2-1

TDU 120e User Manual

5-23

Image 85

ADTRAN TDU 120e user manual Nx/DBU 0.1 Menu Items, Nx56/64 Config

Contents

TDU 120e Trademarks Important Safety Instructions Save These Important Safety Instructions REN/SOC FIC Usoc Affidavit Requirements for Connection to Digital Services Page Vii Canadian Emissions Requirements Canadian Equipment Limitations Limited Product Warranty Presales Inquiries and Applications Support Customer Service, Product Support Information, and TrainingPost-Sale Support Training Repair and Return Table of Contents Operation Status Menu Configuration Menu Port Configuration Port Config Nx/DBU 0.1 Menu Items Remote/Management Menus Xmodem Table of Contents Bridge, PBX, Video Conferencing Application Set-up List of Figures List of Figures Xxii List of Tables List of Tables Xxiv TDU 120e Overview Introduction Introduction Standard Features in the TDU 120e DSX-1 TDU 120e Option ModulesOCU DP DSU DP TDU 120e Option Modules Option Module Architecture Router, PBX, Video Conferencing Application TDU 120e Configuration Applications UNPACK, INSPECT, Power UP InstallationReceipt Inspection Adtran Shipments AC Powered Units Power ConnectionDC Powered Units Customer Provides Grounding Instructions Installation TDU 120e Rear Panels Identification of Rear Panel Layout Network Interface TDU 120e Interfaces DS-1 PBX Interface External Alarm ConnectorControl In Port Craft Port Self-Test Power UP Testing Set User Passcode InitializationSet Unit Identification Set Control Port Chain In/Chain Out Chain In PC Normal POWER-UP Procedure Installation Menu Operation Operation General Menu Traversal Sample Terminal Screen with TDU 120e MenuMain Menu Select and Activate a Menu Item Example of Basic Menu Travel Step Action Result Edit the Data Field Data Port IdentificationExit Any Menu Field Operation or Display Telnet/Terminal Main Menu Menu Structure Menu Options Front Panel Management ConfigurationFlash Download Quit Session Remote LED ACO SwitchCraft Port Network Monitor Jack LED LEDs Port Status LEDs Port 1.1 Option Card Monitor Jacks Alternate Methods of Control Setting up the TDU 120e to Work over a LANWatch PRO Adtran PC Program Step Action Snmp Setting up the TDU 120e to Work over an EIA-232 Connection Status Status Menu Network NI Performance Reports Where MeansSES UAS Active Alarms Network Interface NI Errors Port Status View History DTE Status Nx/DBU 0.1 Menu Items DTE Data/ClockDTE Port Rate DBU Control DBU Data/CNTRLDBU Status Remote Port DS-1 0.2 Menu Items DS-1 ErrorsSlip Ethernet Status Clear Port AlarmLNK CPU Config Configuration Menu TDU 120e Config Menu Tree Network NI Menu Tree Unit Menu Tree Network NI Menu Items Network NI Timing Mode Network Timed Clock Source Network Timed Base DS-1 Timed Clock Source Base DS-1 Base DTE Timed Clock Source Base DTE Timing Internal Clock Source Internal Timing Secondary Clock Source Secondary Timing Normal CSU Normal CSU Timing ATT & FT1, Reject ALL Alarm Report Unit Menu Alarm FormatBPV Threshold Exit Control Port Default RouterIP Address Subnet Address OFF Map ExchangeAuto DS0 Map a and DS0 Map B Map In UseDS0 Map a DS0 Map B 10. DS0 Temp Map DS0 Maps Configuration Menu Step Explanation Creating a DSO MapInitializing the Temp Map If you want to Enter selections Step Action Explanation Editing the Temp MapApplying the Temp Map Copying Map Copy Map a B to Temp Map Reviewing MapsCreate Temp Map Review Map a B Port Configuration Port ConfigReview Temp Map Edit Temp Map Nx/DBU 0.1 Menu Items Nx56/64 Config Inhib Dial Backup Config Normal Mode of OperationBackup Mode Backup On Restore Delay Backup DelayRetry Delay Pattern Verify Wkend Lockout Backup Testing Trap in DBU DS-1 0.2 Menu ItemsInband Lpback RBS Start Robbed Bit SignalingRBS End Configuration Menu Util Utility Menu Time/Date Factory RestoreIf you want to Do this Press Escape Unit ID Set PasscodeChange/Set a Passcode Lost Passcode Port Utility Software RevisionMAC Address To Set the Unit Identification Test Test Menu Loopback Tests Network Tests TDU 120e Ansi FDL LLB Ansi FDL PLBAnsi FT1 LLB All Zeros Test Patterns All OnesQrss Pattern Qrss All DS0s None Qrss TST DS0sInstructions for Generating a Qrss Test Pattern Step Action Pattern Result Sync How to Run an End-to-End Test on Fractional DS0s Step Action Test Name What it does Run Self-Test DTE Loopback Port Tests Pattrn REM V.54Results DBU Loopback DBU DATA/CNTRL Cancel TestsDBU TST Result Port Loopback Test Menu Management Configuration Remote Menu AccessRemote/Management Menus Unit Access Table Unit Access Table Command What it does Unit Access Table Commands Snmp Read/Write Community Snmp Read CommunitySnmp Trap Community Host 1 Trap IP Address Host 3 Trap IP Address Host 2 Trap IP AddressHost 4 Trap IP Address System Name Xmodem Flash Download Quit Session Begin Firmware updateTftp Server IP Address Tftp Server File name T120e.biz Remote/Management Menus Appendix a Understanding Snmp What is SNMP?Basic Components of Snmp Network Manager MIB CommandsGetRequest GetNextRequest GetResponse MessageTrap TDU 120e Snmp Access Snmp Trap Configuration RFC1406.MIB Snmp MIB Browser Configuration Snmp MIB Files Appendix A. Understanding Snmp Wiring Appendix B Connector PinoutsNetwork Pin Name Description Control In/Chain Table B-4. Chain-Out Pinout Control-Out/Chain-Out Table B-5. Craft Port Pinout Table B-6. V.35 Pinout for Nx56/64 DTE Nx56/64 DTEPin Base DS-1 PBX 12,13,14,15 Power Alarm10BaseT Appendix C System Messages Alarm MessagesNetwork Interface NI Nx/DBU Interface Zeros Alarm PLL AlarmFifo Alarm DS-1 PBX Interface Status Messages Frame Slip Pattern OffLine Loop Up Port Loop Up Electrical Specifications Appendix D SpecificationsT1/FT1 Interface CTS, DCD, DSR Nx/DBU Interface Port 0.1-Nx56/64 V.35 Interface DS-1 Interface Port Management Interfaces Receiver RateOption Slot Interface Environmental Specifications Chassis Specification Numerics Index Index 61202156L2-1 Index-3 Index-4