Advantech AIMB-210 2.4 USB Ports (LAN1_USB12/LAN2

AIMB-210 User Manual 16

2.4 USB Ports (LAN1_USB12/LAN2_USB34/USB56/USB78)

The AIMB-210 provides up to eight ports of USB (Universal Serial Bus). The USB

interface complies with USB Specification Rev. 2.0 supporting transmission rate up to

480 Mbps and is fuse protected. The USB interface can be disabled in the system

BIOS setup.

The AIMB-210 is equipped with one high-performance 1000 Mbps Ethernet LANs.

They are supported by all major network operating systems. The RJ-45 jacks on the

rear plate provide convenient or 1000 Mbps operation.

USB56

USB78

Table 2.1: LAN LED Indicator

LAN Mode Lan Indicator

1 Gbps Link on LED1 Green on

100 Mbps Link on LED1 Orange on

Active LED2 Green flash

LAN2_USB34 LAN1_USB12

LAN1_USB12 LAN2_USB34

Contents

Main Copyright Acknowledgements A Message to the Customer Declaration of Conformity Memory Compatibility Ordering Information Product Warranty (2 years) Initial Inspection Page Contents Chapter 1 General Information ............................1 Chapter 2 Connecting Peripherals ....................13 Chapter 3 BIOS Operation .................................35 Chapter 4 Chipset Software Installation Utility 53 Chapter 5 VGA Setup .........................................57 Chapter 6 LAN Configuration ............................59 Appendix A Programming the Watchdog Timer..61 Appendix B I/O Pin Assignments..........................69 Page Page 1.1 Introduction 1.2 Features 1.3 Specifications 1.3.1 System 1.3.2 Memory 1.3.3 Input/Output 1.3.4 Graphics 1.4 Jumpers and Connectors Table 1.1: Jumpers Table 1.2: Connectors Page AIMB-210 User Manual 6 1.5 Board layout: Jumper and Connector Locations wryi qetu Figure 1.1 Jumper and Connector Location Figure 1.2 I/O Connectors Page 1.7 Safety Precautions 1.8 Jumper Settings 1.8.1 How to Set Jumpers 1.8.2 CMOS Clear (CMOS1) Table 1.3: CMOS1 1.8.3 COM2 RS 232/422/485 Mode Selector (JSETCOM2) 1.8.4 JLV1/JLV2: LCD Power 3.3 V/5 V Selector Table 1.4: COM2 RS 232/422/485 Mode Selector (JSETCOM2) RS232* RS422 RS485 Table 1.5: JLV1/JLV2: LCD Power 3.3 V/5 V Selector 1.8.5 JPSON1: ATX, AT Mode Selector 1 1 1 1 1.8.6 JWDT1: Watchdog Timer Output Option Table 1.6: JPSON1: ATX, AT Mode Selector 1.9 System Memory 1.10 Memory Installation Procedures Page Page Page 2.4 USB Ports (LAN1_USB12/LAN2_USB34/USB56/ USB78) Table 2.1: LAN LED Indicator 2.5 TV-Out Connector (TVOUT1) Table 2.2: TV-Out Connector (TVOUT1) 2.6 VGA Connector (VGA1) 2.7 Serial Ports (COM1~COM6) Page Page Page 2.11 Front Panel Connectors (JFP1/JFP2/JFP3) 2.11.5 Power LED and keyboard lock connector (JFP3 / PWR_LED & KEY LOCK) Table 2.3: ATX power supply LED status (No support for AT power) Page Page Page Page Page Page Page Page Page Page Page 3.1 Introduction 3.2 BIOS Setup 3.2.1 Main Menu 3.2.2 Standard CMOS Features 3.2.3 Advanced BIOS Features 3.2.4 Advanced Chipset Features Page 3.2.5 Integrated Peripherals Page 3.2.6 USB Device Setting Page 3.2.9 Power Management Setup Page 3.2.10 PnP/PCI Configurations 3.2.11 PC Health Status 3.2.12 Frequency/Voltage Control Page Page Page Page 4.1 Before You Begin 4.2 Introduction Page Page Page 5.1 Introduction 5.2 Windows Vista/XP/2000 Page Page Page A.1 Programming the Watchdog Timer A.1.1 Watchdog Timer Overview A.1.2 Programming the Watchdog Timer Page Table A.1: Watchdog Timer Registers A.1.3 Example Program Page Page Page Page B.1 Parallel Port (LPT1) * Low activity B.2 USB Header (USB56, USB78) Table B.1: Parallel Port (LPT1) Table B.2: USB Header (USB56) B.3 VGA Connector (VGA1) B.4 RS-232 Interface Table B.3: VGA Connector (VGA1) Table B.4: RS-232 Interface (COM1~COM4) B.5 RS-232/422/485 Setting Interface (JETCOM2) B.6 SPI_CN1: SPI Fresh Card Pin Connector B.7 PS/2 Keyboard and Mouse Connector (KBMS1) B.8 CPU Fan Power Connector (CPU_FAN1) Table B.7: PS/2 Keyboard and Mouse Connector (KBMS1) Table B.8: CPU Fan Power Connector (CPU_FAN1) B.9 System Fan Power Connector (CHA_FAN1) B.10 Power LED & Keyboard Lock Connector (JFP3) Table B.9: System Fan Power Connector (SYSFAN1/SYSFAN2) Table B.10: Power LED & Keyboard Lock Connector (JFP3) Page B.13 ATX Power Connector (EATXPWR1) B.14 USB/LAN ports (LAN1_USB12/LAN2_USB34) Table B.13: ATX Power Connector (ATX2) Table B.14: USB Port Table B.15: Ethernet 10/100 Mbps RJ-45 Port B.15 Line In, Line Out, Mic In Connector (AUDIO1) B.16 Serial ATA0/1 (SATA1/SATA2) B.18 AC-97 Audio Interface (FPAUD1) B.17 AT/ATX Mode (PSON1) Table B.16: Serial ATA 0/1 (SATA1/SATA2) B.19 GPIO Pin Header (GPIO1) Table B.19: AT/ATX Mode (PSON1) B.20 LVDS Connector: LVDS1 & LVDS2 (Optional) Table B.20: LVDS1 Connector (Optional) B.21 LVDS Power Jumper (JLV1, JLV2) * default setting Table B.21: LVDS2 Connector (Optional) Table B.22: LVDS Power Jumper B.22 LVDS Invert: INV1 & INV2 (Optional) B.23 System I/O Ports Table B.23: LVDS Power Jumper Table B.24: System I/O Ports B.24 DMA Channel Assignments B.25 Interrupt Assignments B.26 1st MB Memory Map Table B.25: DMA Channel Assignments Table B.26: Interrupt Assignments Page www.advantech.com