Soaking duration, Opening and closing the filling door | AEG 88830

Instructions for use

Soaking duration

If you keep button SOAKING (TREMPAGE) depressed and at the same time actuate the TIMER DELAY button (DEPART DIFFERE) you can extend the soaking duration from 1 up to a maximum of 19 hours.

3 Without a preselected time the soaking duration is approx. 1 hour.

Opening and closing the filling door

0 Open: Press button DOOR/LIGHT (PORTE/LUMIERE). The filling door springs open.

0Close: Press the filling door firmly closed.

The DOOR/LIGHT (PORTE/LUMIERE) illumination shows whether the fill- ing door can be opened while the appliance is switched on :

–green: The door can be opened (not when the program saving func- tion is activated, for details see the section Program Saving“)

– off:

Door cannot be opened temporarily

–red: Door is open

3	The washing drum is illuminated when the filling door is open. The illu-
	mination goes out automatically after approx. 3 minutes.
Add the Washing
3	For the maximum filling quantities, refer to the ”Program Tables”.
	For information on the correct preparation of the washing,

see ”Sort and Prepare the Washing”.

0 1. Sort and prepare the washing according to type.

2.Open the filling door: Press the button DOOR/LIGHT (PORTE/LUMIERE). The door springs open.

3.Fill with washing.

Attention! When closing the door, make sure no items of washing get stuck! This could damage textiles and the unit.

4.Close the filling door securely.

22

Image 22

AEG 88830 manual Soaking duration, Opening and closing the filling door, Add the Washing

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do if Contents Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General Safety Dispose the packing material DisposalEnvironment Tips For polyoxymethylene, e.g. plastic clips Front View Unit DescriptionDrawer for Washing Powder and Care Agent Control panel Program Selector Wool LAINE/ P Handwash Program Silk SOIE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua Alarm Prepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes How much washing detergent and care agent? Water Softener Brief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to Adapted depending on the washing program Set the delay timer/soaking duration Delay timerChange the spin speed/Select rinse hold COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Opening and closing the filling door Soaking durationAdd the Washing Section Washing Detergents and Care Agents If using Liquid Detergent/TabsAdd Washing Detergent and/Care Agent Or for water softener If the delay timer is set Start the washing program Multi-display Completion of the Washing ProgramProgram sequence display Display Residual MOISTURE%/LOADING% It again Washing cycle is finished/Remove the washingAbort program Program is finished Too much detergent was used in the just finished Program Tables Washing Separate Conditioning/Starching/Impregnating Separate Spin Cleaning and Care Washing Detergent Drawer Washing Drum Filling Door Pump Cleaning the drain pumpBefore cleaning the drain pump Gency Emptying Remedying Faults What to do if Not been removed Turn off the tap, then Open the water valve fully If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinse Carry Out an Emergency Emptying Operation Additional Rinse RINSE+ When all the washing solution has drained offEmergency Unlocking of the Filling Door Set Additional Rinse Time Solution CoolingCancel Additional Rinse Cycle before pumping off by incoming cold water Set the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Feature Child Safety FeatureSetting the Child Safety Cancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for Installation When transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the Unit Firmly pull both hose holders off the unit Close off the hole with the plug cap G Setting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Delivery Heads over 1m Technical DataDimensions Measurements in mmPage Index Service When do you incur costs even during the warranty period?