Washing cycle is finished/Remove the washing, It again | AEG 88830

Instructions for use

Abort program

0Turn the program selector to OFF (ARRET) to abort the washing program.

3	The washing program can be interrupted at any time by pressing the
	START/PAUSE (MARCHE/PAUSE) button and then continued by pressing

it again.

The washing cycle is finished/Remove the washing.

	END (FIN) is lit at the program sequence display when a washing
	program is finished.
3	The washing machine switches itself into the stand-by mode if no
	button is pressed or the program selector is not turned within approx.

3 minutes after the end of the program. Only END (FIN) is illuminated. All other displays on the control panel are switched off in order to save energy. Pressing any arbitrary button cancels the stand-by mode.

• A crease protection phase of approx. 30 minutes follows at the end of the program if program EASY IRON (SANS REPASSAGE) had been selected. The multidisplay also shows the remaining time and the display END (FIN) is illuminated. You can open the filling door and take the washing out at any time during the crease protection phase.

• START/PAUSE (MARCHE/PAUSE) flashes if spin speed 0 (rinse hold ) was selected.

0 1. After a rinse hold it is first of all necessary to pump off the water:

–Either press START/PAUSE (MARCHE/PAUSE) button (the washing will be spun according to the just finished program; with the SPIN SPEED (VITESSE D´ESSORAGE) button the spin speed can be changed even during the spin-drying process), or

–turn program selector to PUMP (VIDANGE) and then press START/ PAUSE (MARCHE/PAUSE) button (the water is pumped off without a spin), or

–Turn the program selector to SPIN (ESSORAGE) or to SHORT SPIN (ESSORAGE DELICAT) and press START/PAUSE (MARCHE/PAUSE)

button (the washing is spin-dried normally or with a short spin). END (FIN) is illuminated at the end of this program step.

2.Open the filling door.

As soon as DOOR/LIGHT (PORTE/LUMIERE) is illuminated in green the door can be opened (not if program saving is active, see "Program Sav- ing").

3.Remove the washing.

26

Image 26

AEG 88830 manual Washing cycle is finished/Remove the washing, Abort program, It again, Program is finished

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do if Contents Correct Use SafetyBefore Putting into Operation for the First Time Child Safety General Safety Dispose the packing material DisposalEnvironment Tips For polyoxymethylene, e.g. plastic clips Drawer for Washing Powder and Care Agent Unit DescriptionFront View Control panel Program Selector Wool LAINE/ P Handwash Program Silk SOIE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes How much washing detergent and care agent? Water Softener After the Washing Program Ends Run a Washing CycleBrief Instructions Set the program selector to Setting the Washing ProgramPossible additional programs to suit the type of washing Adapted depending on the washing program Set the delay timer/soaking duration Delay timerChange the spin speed/Select rinse hold COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Add the Washing Soaking durationOpening and closing the filling door Section Washing Detergents and Care Agents If using Liquid Detergent/TabsAdd Washing Detergent and/Care Agent Or for water softener If the delay timer is set Start the washing program Multi-display Completion of the Washing ProgramProgram sequence display Display Residual MOISTURE%/LOADING% It again Washing cycle is finished/Remove the washingAbort program Program is finished Too much detergent was used in the just finished Program Tables Washing Separate Conditioning/Starching/Impregnating Separate Spin Cleaning and Care Washing Detergent Drawer Washing Drum Filling Door Pump Cleaning the drain pumpBefore cleaning the drain pump Gency Emptying Remedying Faults What to do if Not been removed Turn off the tap, then Open the water valve fully If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinse Carry Out an Emergency Emptying Operation Additional Rinse RINSE+ When all the washing solution has drained offEmergency Unlocking of the Filling Door Set Additional Rinse Time Solution CoolingCancel Additional Rinse Cycle before pumping off by incoming cold water Cancel the Solution Cooling Additional Rinse and Solution CoolingSet the Solution Cooling Program Saving Setting the Program Saving FunctionCanceling the Program Saving Function Feature Child Safety FeatureSetting the Child Safety Cancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for Installation When transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the Unit Firmly pull both hose holders off the unit Close off the hole with the plug cap G Setting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Delivery Heads over 1m Technical DataDimensions Measurements in mmPage Index Service When do you incur costs even during the warranty period?