Technical Data, Dimensions, Delivery Heads over 1m | AEG 88830

Setting up and connection instructions

Delivery Heads over 1m

To pump off the washing / rinsing agent, every washing machine has a pump which transports liquids via the drainage hose up to a height of 1m, calculated from the machine's floor.

For delivery heads over 1m, consult the Customer Service.

Technical Data

Height adjustment	Approx. +10/-5mm
Filling quantity	max. 5kg
(program-dependent)
Use	Domestic
Drum speed, spin	see rating plate
Water pressure	1-10bar
	(=10–100N/cm2= 0.1–1.0MPa)
Dimensions

(Measurements in mm)

52

Image 52

AEG 88830 manual Technical Data, Dimensions, Delivery Heads over 1m, Measurements in mm

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do if Contents Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General Safety Disposal Environment TipsDispose the packing material For polyoxymethylene, e.g. plastic clips Front View Unit DescriptionDrawer for Washing Powder and Care Agent Control panel Program Selector Wool LAINE/ P Handwash Program Silk SOIE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua Alarm Prepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes How much washing detergent and care agent? Water Softener Brief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to Set the delay timer/soaking duration Delay timer Change the spin speed/Select rinse holdAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Opening and closing the filling door Soaking durationAdd the Washing If using Liquid Detergent/Tabs Add Washing Detergent and/Care AgentSection Washing Detergents and Care Agents Or for water softener If the delay timer is set Start the washing program Completion of the Washing Program Program sequence displayMulti-display Display Residual MOISTURE%/LOADING% Washing cycle is finished/Remove the washing Abort programIt again Program is finished Too much detergent was used in the just finished Program Tables Washing Separate Conditioning/Starching/Impregnating Separate Spin Cleaning and Care Washing Detergent Drawer Washing Drum Filling Door Cleaning the drain pump Before cleaning the drain pumpPump Gency Emptying Remedying Faults What to do if Not been removed Turn off the tap, then Open the water valve fully If the washing result is not satisfactory If the washing is grey and limescale forms in the drumIf there are still grey stains on the washing If foam is still visible after the final rinse Carry Out an Emergency Emptying Operation When all the washing solution has drained off Emergency Unlocking of the Filling DoorAdditional Rinse RINSE+ Set Additional Rinse Solution Cooling Cancel Additional RinseTime Cycle before pumping off by incoming cold water Set the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Child Safety Feature Setting the Child SafetyFeature Cancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for Installation Setting Up the Unit Remove the Transport SafeguardWhen transporting the unit with a sack trolley Transporting the Unit Firmly pull both hose holders off the unit Close off the hole with the plug cap G Setting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Technical Data DimensionsDelivery Heads over 1m Measurements in mmPage Index Service When do you incur costs even during the warranty period?