Child Safety Feature, Setting the Child Safety | AEG 88830 specs

Instructions for use

Child Safety Feature

	When the child safety feature is
	used, the filling door can no
	longer be closed and no more
	washing programs can be started.
	Setting the Child Safety
	Feature:
0	Use a coin to turn the rotary knob
	(on the inside of the filling door)
	clockwise as far as it will go.
1	Warning! The rotary knob must
	not be pressed in following adjust-

ment, otherwise the child safety feature is not active. The rotary knob must project as shown in the diagram.

Cancelling the Child Safety

Feature:

0Turn the rotary knob anticlockwise as far as it will go.

43

Image 43

AEG 88830 manual Setting the Child Safety, Cancelling the Child Safety Feature

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents What to do if Solution Cooling Contents Before Putting into Operation for the First Time SafetyCorrect Use General Safety Child Safety For polyoxymethylene, e.g. plastic clips DisposalEnvironment Tips Dispose the packing material Front View Unit DescriptionDrawer for Washing Powder and Care Agent Program Selector Control panel Silk SOIE/ P Handwash Program Wool LAINE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display Water Protection Aqua Control + Aqua Alarm What Does Update Mean? Prepare the Washing Cycle Before the First WashSort and Prepare the Washing Washing Types and Care Codes Water Softener How much washing detergent and care agent? Brief Instructions Run a Washing CycleAfter the Washing Program Ends Possible additional programs to suit the type of washing Setting the Washing ProgramSet the program selector to COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Set the delay timer/soaking duration Delay timerChange the spin speed/Select rinse hold Adapted depending on the washing program Opening and closing the filling door Soaking durationAdd the Washing Or for water softener If using Liquid Detergent/TabsAdd Washing Detergent and/Care Agent Section Washing Detergents and Care Agents Start the washing program If the delay timer is set Display Residual MOISTURE%/LOADING% Completion of the Washing ProgramProgram sequence display Multi-display Program is finished Washing cycle is finished/Remove the washingAbort program It again Too much detergent was used in the just finished Washing Program Tables Separate Spin Separate Conditioning/Starching/Impregnating Washing Detergent Drawer Cleaning and Care Filling Door Washing Drum Gency Emptying Cleaning the drain pumpBefore cleaning the drain pump Pump What to do if Remedying Faults Not been removed Turn off the tap, then Open the water valve fully If foam is still visible after the final rinse If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If there are still grey stains on the washing Carry Out an Emergency Emptying Operation Set Additional Rinse When all the washing solution has drained offEmergency Unlocking of the Filling Door Additional Rinse RINSE+ Cycle before pumping off by incoming cold water Solution CoolingCancel Additional Rinse Time Set the Solution Cooling Additional Rinse and Solution CoolingCancel the Solution Cooling Canceling the Program Saving Function Setting the Program Saving FunctionProgram Saving Cancelling the Child Safety Feature Child Safety FeatureSetting the Child Safety Feature Safety Instructions for Installation Setting UP and Connection Instructions Transporting the Unit Setting Up the UnitRemove the Transport Safeguard When transporting the unit with a sack trolley Close off the hole with the plug cap G Firmly pull both hose holders off the unit Setting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Measurements in mm Technical DataDimensions Delivery Heads over 1mPage Index When do you incur costs even during the warranty period? Service