Water Inflow | AEG 88830 manual

Setting up and connection instructions

Water Inflow

A pressure hose 1.5m in length is supplied.

If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible.

–Sets of hoses in lengths of 2.2m, 3.5m and 5m are available for washing machines without Aqua-Control.

–Sets of hoses in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control.

Attention! Never cut into pieces in order to extend the hoses!

3	Sealing rings are supplied either in the plastic
	nuts of the hose screw connection or in the

enclosed pack. Do not use other seals!

0 1. Connect the hose with the angled connection to the machine.

Attention!

– Do not lay the supply hose vertically downwards. Rather, turn it to the right or left as shown in the diagram.

– Only tighten the screw connection manually.

2. Connect the hose with the

straight connection to a water tap with a screw thread of R 3/4 (inches).

Attention! Only tighten the screw connection manually.

3. By slowly opening the water tap before putting the washing machine into operation, check whether the connection is free of leaks.

50

Image 50

AEG 88830 manual Water Inflow

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do if Contents Correct Use SafetyBefore Putting into Operation for the First Time Child Safety General Safety Dispose the packing material DisposalEnvironment Tips For polyoxymethylene, e.g. plastic clips Drawer for Washing Powder and Care Agent Unit DescriptionFront View Control panel Program Selector Wool LAINE/ P Handwash Program Silk SOIE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes How much washing detergent and care agent? Water Softener After the Washing Program Ends Run a Washing CycleBrief Instructions Set the program selector to Setting the Washing ProgramPossible additional programs to suit the type of washing Adapted depending on the washing program Set the delay timer/soaking duration Delay timerChange the spin speed/Select rinse hold COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Add the Washing Soaking durationOpening and closing the filling door Section Washing Detergents and Care Agents If using Liquid Detergent/TabsAdd Washing Detergent and/Care Agent Or for water softener If the delay timer is set Start the washing program Multi-display Completion of the Washing ProgramProgram sequence display Display Residual MOISTURE%/LOADING% It again Washing cycle is finished/Remove the washingAbort program Program is finished Too much detergent was used in the just finished Program Tables Washing Separate Conditioning/Starching/Impregnating Separate Spin Cleaning and Care Washing Detergent Drawer Washing Drum Filling Door Pump Cleaning the drain pumpBefore cleaning the drain pump Gency Emptying Remedying Faults What to do if Not been removed Turn off the tap, then Open the water valve fully If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinse Carry Out an Emergency Emptying Operation Additional Rinse RINSE+ When all the washing solution has drained offEmergency Unlocking of the Filling Door Set Additional Rinse Time Solution CoolingCancel Additional Rinse Cycle before pumping off by incoming cold water Cancel the Solution Cooling Additional Rinse and Solution CoolingSet the Solution Cooling Program Saving Setting the Program Saving FunctionCanceling the Program Saving Function Feature Child Safety FeatureSetting the Child Safety Cancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for Installation When transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the Unit Firmly pull both hose holders off the unit Close off the hole with the plug cap G Setting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Delivery Heads over 1m Technical DataDimensions Measurements in mmPage Index Service When do you incur costs even during the warranty period?