Setting UP and Connection Instructions | AEG 88830 guide

Setting up and connection instructions

SETTING UP AND CONNECTION

INSTRUCTIONS

Safety Instructions for Installation

•Do not tilt the washing machine onto its front or onto its right side (looking from the front). Electrical components could get wet!

•Check the washing machine for transport damage. Never connect a damaged unit. Consult your supplier in the event of damage.

•Ensure that all parts of the transport safeguard have been removed and that the splash guard is fitted to the unit, see ”Removing the Transport Safeguard”. Otherwise, damage to the unit or to adjacent furniture could occur during spinning.

•Always insert the plug into a correctly installed PE socket.

•In the case of permanent installation: A permanent installation may only be made by an authorised specialist.

•Before putting the unit into operation, ensure that the rated voltage and current type shown on the unit's rating plate are the same as the mains voltage and current type at the installation location. The required electrical fuse is also shown on the rating plate.

•The mains cable may only be replaced by the Customer Service or by an authorised specialist.

44

Image 44

AEG 88830 manual Setting UP and Connection Instructions, Safety Instructions for Installation

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do if Contents Correct Use SafetyBefore Putting into Operation for the First Time Child Safety General Safety Disposal Environment TipsDispose the packing material For polyoxymethylene, e.g. plastic clips Drawer for Washing Powder and Care Agent Unit DescriptionFront View Control panel Program Selector Wool LAINE/ P Handwash Program Silk SOIE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua Alarm Sort and Prepare the Washing Before the First WashPrepare the Washing Cycle Washing Types and Care Codes How much washing detergent and care agent? Water Softener After the Washing Program Ends Run a Washing CycleBrief Instructions Set the program selector to Setting the Washing ProgramPossible additional programs to suit the type of washing Set the delay timer/soaking duration Delay timer Change the spin speed/Select rinse holdAdapted depending on the washing program COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Add the Washing Soaking durationOpening and closing the filling door If using Liquid Detergent/Tabs Add Washing Detergent and/Care AgentSection Washing Detergents and Care Agents Or for water softener If the delay timer is set Start the washing program Completion of the Washing Program Program sequence displayMulti-display Display Residual MOISTURE%/LOADING% Washing cycle is finished/Remove the washing Abort programIt again Program is finished Too much detergent was used in the just finished Program Tables Washing Separate Conditioning/Starching/Impregnating Separate Spin Cleaning and Care Washing Detergent Drawer Washing Drum Filling Door Cleaning the drain pump Before cleaning the drain pumpPump Gency Emptying Remedying Faults What to do if Not been removed Turn off the tap, then Open the water valve fully If the washing result is not satisfactory If the washing is grey and limescale forms in the drumIf there are still grey stains on the washing If foam is still visible after the final rinse Carry Out an Emergency Emptying Operation When all the washing solution has drained off Emergency Unlocking of the Filling DoorAdditional Rinse RINSE+ Set Additional Rinse Solution Cooling Cancel Additional RinseTime Cycle before pumping off by incoming cold water Cancel the Solution Cooling Additional Rinse and Solution CoolingSet the Solution Cooling Program Saving Setting the Program Saving FunctionCanceling the Program Saving Function Child Safety Feature Setting the Child SafetyFeature Cancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for Installation Setting Up the Unit Remove the Transport SafeguardWhen transporting the unit with a sack trolley Transporting the Unit Firmly pull both hose holders off the unit Close off the hole with the plug cap G Setting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Technical Data DimensionsDelivery Heads over 1m Measurements in mmPage Index Service When do you incur costs even during the warranty period?