How much washing detergent and care agent? | AEG 88830 specs

Instructions for use

Washing Detergents and Care Agents

	Which washing detergnet and care agent?
	Use only washing detergents and care agents which are suitable for use
	in washing machines. Always follow the manufacturer's instructions.
	How much washing detergent and care agent?
	The amount to be used depends on:
	• the dirtiness of the washing
	• the hardness category of the mains water supply
	• the filling quantity
2	If the detergent manufacturer gives no details of the dosing quantities
	for minimum loads, add one third less for half loads and, in the case of

very small loads and for EASY IRON (SANS REPASSAGE), only half the amount of detergent recommended for a full load.

Refer to the detergent/care manufacturer's instructions on use and dosage.

Water Softener

For medium to high water hardness (hardness category II or higher) you should use water softener. Pay attention to the manufacturer's instruc- tions. Always then meter detergent for hardness category I (= soft). The responsible water works can provide information on the local water hardness.

2	Since the water softener is added before the main washing detergent,
	(water pre-softening), eighty percent of the softener quantity stated on
	the package is sufficient.
	Water Hardness Details

			Water Hardness °dH		Water Hardness in mmol/l
		Hardness Category		(degrees German	Water Hardness in mmol/l
		Hardness Category		(degrees German	(millimol per litre)
				hardness)	(millimol per litre)
				hardness)
		I – soft		0 - 7	up to 1.3

		II – medium hard		7 - 14	1.3 - 2.5
		III – hard		14 - 21	2.5 - 3.8
		IV – very hard		over 21	over 3.8

18

Image 18

AEG 88830 manual How much washing detergent and care agent?, Water Softener

Contents

ÖKO-LAVAMAT 88830 update Dear customer Contents Solution Cooling What to do if Contents Safety Before Putting into Operation for the First TimeCorrect Use Child Safety General Safety Dispose the packing material DisposalEnvironment Tips For polyoxymethylene, e.g. plastic clips Unit Description Front ViewDrawer for Washing Powder and Care Agent Control panel Program Selector Wool LAINE/ P Handwash Program Silk SOIE/ P Handwash Program Additional Program Buttons Consumption Values and Time Requirements Running Time Display What Does Update Mean? Water Protection Aqua Control + Aqua Alarm Before the First Wash Prepare the Washing CycleSort and Prepare the Washing Washing Types and Care Codes How much washing detergent and care agent? Water Softener Run a Washing Cycle Brief InstructionsAfter the Washing Program Ends Setting the Washing Program Possible additional programs to suit the type of washingSet the program selector to Adapted depending on the washing program Set the delay timer/soaking duration Delay timerChange the spin speed/Select rinse hold COTTONS/LINEN BLANC/COULEURS 1800 revolutions per minute Soaking duration Opening and closing the filling doorAdd the Washing Section Washing Detergents and Care Agents If using Liquid Detergent/TabsAdd Washing Detergent and/Care Agent Or for water softener If the delay timer is set Start the washing program Multi-display Completion of the Washing ProgramProgram sequence display Display Residual MOISTURE%/LOADING% It again Washing cycle is finished/Remove the washingAbort program Program is finished Too much detergent was used in the just finished Program Tables Washing Separate Conditioning/Starching/Impregnating Separate Spin Cleaning and Care Washing Detergent Drawer Washing Drum Filling Door Pump Cleaning the drain pumpBefore cleaning the drain pump Gency Emptying Remedying Faults What to do if Not been removed Turn off the tap, then Open the water valve fully If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinse Carry Out an Emergency Emptying Operation Additional Rinse RINSE+ When all the washing solution has drained offEmergency Unlocking of the Filling Door Set Additional Rinse Time Solution CoolingCancel Additional Rinse Cycle before pumping off by incoming cold water Additional Rinse and Solution Cooling Set the Solution CoolingCancel the Solution Cooling Setting the Program Saving Function Canceling the Program Saving FunctionProgram Saving Feature Child Safety FeatureSetting the Child Safety Cancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for Installation When transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the Unit Firmly pull both hose holders off the unit Close off the hole with the plug cap G Prepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Delivery Heads over 1m Technical DataDimensions Measurements in mmPage Index Service When do you incur costs even during the warranty period?