Agilent Technologies 81101A Default Values, Standard Settings

Programming Reference

Default Values, Standard Settings

Default Values, Standard Settings

Parameter *RST, Default Values

:ARM : EWIDth:STATe OFF

:FREQuency 100kHz

:IMPedance 50Ω

:LEVel +1.00V

:PERiod 10.00µs

:SENSe EDGE

:SLOPe POS

:SOURce IMMediate

:DISPlay [:WINDow] [:STATe] ON

:MMEMory :CATalog? not applicable

:CDIRectory not applicable

:COPY not applicable

:DELete not applicable

:INITialize not applicable

:LOAD :STATe not applicable

:STORe:STATe not applicable

:OUTPut[1][:NORMal][:STATe] OFF

:IMPedance[:INTernal] 50Ω

:EXTernal 50.0Ω

:POLarity NORMal

[:SOURce]:CURRent[1][:LEVel][:IMM][:AMPL] 20.0mA (from 50Ω into 50Ω)

:OFFset 0.0mA (from 50Ω into 50Ω)

:HIGH +10.0mA (from 50Ω into 50Ω)

:LOW –10.0mA (from 50Ω into 50Ω)

:LIMit[:HIGH] +10.0mA

Contents

Main MODIFY Front Panel Display and Softkeys Page Notice Copyright Notice Warra nty Limitation of Warranty Exclusive Remedies Certification Services and Support Safety Summary General Environmental Conditions Before Applying Power Ground the Instrument Fuses Do Not Operate in an Explosive Atmosphere Do Not Remove the Instrument Cover Safety Symbols About this Book Conventions Used in this Book Page Contents Page The GP-IB Interface Bus Agilent 81101A Remote Control Programming Recommendations Page Common Command Summary 19 General Programming Aspects Status Model Status Model Condition Register Transition Filters Event Register Enable Register Status Byte Standard Event Status Group OPERation Status Group QUEStionable Status Group 2 Agilent 81101A SCPI Command Summary Page Page Page Page Default Values, Standard Settings Page Page Page Programming the Instrument Trigger Modes Continuous Triggered Gated External Width Pulses Burst SCPI Instrument Command List Page Page Page Page Page Page Page Page Page Page Offset = High Low Page Page Page Page Period = 1 Frequency Page D elay = Phase 360 Period Width = Duty Cycle 100 Period Phase = Delay Period Delay% = Delay Period Page Page DblDel% = DblDel Period Page Frequency = 1 Page Page Page Page Page Page Page High = Offset + Amplitude Low = Offset Amplitude High = Offset + Amplitude Low = Offset Amplitude Page HighLow Offset = Page Page Page 77 5. :STATus:QUEStionable:PTRansition 4. :STATus:QUEStionable:NTRansition Page Page Page Page Page Page Page Page Page Page Page 3 90 Specifications Declaration of Conformity Declaration of Conformity Manufacturer Safety EMC Supplementary Information Agilent 81101A Specifications General Page Timing Specifications Period Glitch-free timing changes Width Delay Double Pulse Delay Transition Times Level Specifications External Load compensation Level Parameters Pulse Performance Clock Sources Clock / PLL Reference Input Phase Locked Loop (PLL) External Clock Output Modes Pulses Mode Burst Mode Trigger Modes 101 Specifications Agilent 81101A Specifications Trigger and Strobe Specifications Trigger Output Strobe Output Typical Delays Human Interface Memory Remote Control Pulse Parameter Definitions Time Reference Point Pulse Period Trigger Delay Pulse Width Pulse Delay Double Pulse Delay Interchannel Delay (Skew) Transition Time Linearity Jitter Stability Pulse Levels Preshoot, Overshoot, Ringing Settling Time Page Page Page Page Page Page Front Panel Controls Page MANUAL CHANGES September, 01 Page Page Page